Search results

  1. HighTrim

    Power tilt 1988 evinrude 40hp

    Re: Power tilt 1988 evinrude 40hp FIrst thing that you should do is order yourself a manual, they will honestly pay for themselves a million times over. Here is the parts break down though. Or you can go to this link and follow it for yourself, it will itemize all the parts for you. After the...
  2. HighTrim

    OMC control box for tilt trim or not!!!!!!!!!!

    Re: OMC control box for tilt trim or not!!!!!!!!!! Ok the wiring diagram for your motor is posted below, Im not quite sure exactly which wiring section you are referring to. All that box is is a junction box, to house the solenoids and connections.
  3. HighTrim

    Evinrude Year manufacture

    Re: Evinrude Year manufacture Could you look for the welch plug, it is about the size of a quarter, silver, and should be on the top rear of the motor, it looks like this. I assume the stern brakcet tag is removed? http://i46.photobucket.com/albums/f1...MVC-859S-1.jpg A pic may also help
  4. HighTrim

    '64 9.5 Evinrude

    Re: '64 9.5 Evinrude To test if for sure, draw a line across the hub and the prop, or use the cotter pin as a center line. Run the motor in the water until you hear it "rev", pull it out, and inspect the lines. If they are no longer lined up, your prop is spun. May want to consider new if the...
  5. HighTrim

    1980 T&T wiring question.

    Re: 1980 T&T wiring question. This will be the wiring diagram then, it is compliments of Ezeke. Ive never seen the gauge wires wired in that fashion before. Ezeke is pretty knowledgeable in this stuff, hopefully he jumps in.
  6. HighTrim

    Anatomy of a Johnson 2-Stroke - learn by numbers

    Re: Anatomy of a Johnson 2-Stroke - learn by numbers This is where you want to lube it.
  7. HighTrim

    87 Evinrude 28 spl Engine Problems?

    Re: 87 Evinrude 28 spl Engine Problems? Draw a line across the hub and prop, or use the cotter pin as a centre line, run it in the water until you hear it "slip", pull it out, then check the lines, if they are no longer lined up, your hub is definately spun. Have it re hubbed like...
  8. HighTrim

    No power

    Re: No power yes the carbs need to be taken off and rebuilt with a bath. There is a special tool needed to remove the jets, or you can make your own as FR did here in the pic. This video may help with your first carb rebuild. http://www.meegsonline.com/tmd/TMDsVideoChronicle2.wmv If you...
  9. HighTrim

    Johnson 30 chokes out when powering up

    Re: Johnson 30 chokes out when powering up TD is right, probably the low speed jet, which will get serviced in your carb rebuild. You will need a special tool to get the jets out, here is a pic TD and FR have posted a few times. THis is the location of the transom bracket tag that he...
  10. HighTrim

    1994 90hp Evinrude

    Re: 1994 90hp Evinrude
  11. HighTrim

    evinrude 135 starflight

    Re: evinrude 135 starflight We will need a model number. First look for the transom tag here: If the tag has been removed because of paint or when it was stolen ;), look for the welch plug, it will be on the top rear of the motor, about the size of a quarter and will look like this...
  12. HighTrim

    1977 Evinrude 115 Tilt Trim Wiring question

    Re: 1977 Evinrude 115 Tilt Trim Wiring question Welcome to iboats! This diagram should help, let me know if you have any more issues. Good luck.
  13. HighTrim

    OMC tilt/trum unit #173827 Vs. #773530

    Re: OMC tilt/trum unit #173827 Vs. #773530 The 2 wire motors are newer and much easier to replace, sources for the 3 wire motors are getting scarce. I will supply wiring diagrams for both. Be sure which unit will fit on your outboard, they mount differently, and you did not mention the year...
  14. HighTrim

    Johnson 85 Outboard- no movement in water

    Re: Johnson 85 Outboard- no movement in water To find the model number, look on the transom bracket, Ive provided a diagram supplied by a member on this forum. If not there due to being painted or what have you, look for a welch plug, it is about the size of a quarter, and should be on the...
  15. HighTrim

    Johnson 85 Outboard- no movement in water

    Re: Johnson 85 Outboard- no movement in water That was my thinking as well, just wanted him to verify the over revving sound. bc, draw a line across the hub and prop, or use the cotter pin as a center line, run it in the water, then pull it out. If the lines are no longer lined up, the prop is...
  16. HighTrim

    Evinrude 115 won't idle?

    Re: Evinrude 115 won't idle? If the model number is not on the freeze plug, look on the transom bracket here for it, it could be possibly painted over though. If the motor is earlier than 1980 these are the model numbers you will have to choose from. If it is 1980 to 1998 or later, it will...
  17. HighTrim

    intermitent eratic cranking behavior

    Re: intermitent eratic cranking behavior This is an example of the switch he was referring to
  18. HighTrim

    Hub or pin?

    Re: Hub or pin? What you are describing is a spun hub if im understanding you correctly. Although I cant see it not spinning on the other 2 outings. Draw a line across the hub and prop or use the cotter pin as a center line, run the motor in the water, then pull it out when you hear it "rev"...
  19. HighTrim

    1977 Johnson Tilt and Trim -could use troubleshooting advice

    Re: 1977 Johnson Tilt and Trim -could use troubleshooting advice here is a wiring diagram of what you should have.
  20. HighTrim

    75 hp stinger seahorse- cracked lower unit

    Re: 75 hp stinger seahorse- cracked lower unit That small circular plate you found is the frost plug, is it about the size of a quarter? The number on it is in fact your model number, post it and we will be able to get the year for you. You prop may be spun, draw a line across the hub and the...
View older results
Top