Search results

  1. HighTrim

    Tach Issue (1985 Evinrude 70HP)

    Re: Tach Issue (1985 Evinrude 70HP) Visual may help.
  2. HighTrim

    1988 15 Hp Johnson - intermittent start

    Re: 1988 15 Hp Johnson - intermittent start Here is the spark tester I was referring to And here is some reading. When was the carb last rebuilt? Let us know what you find. http://forums.iboats.com/showthread.php?t=225510 http://forums.iboats.com/showthread.php?t=158071
  3. HighTrim

    Early 80's Johnson 150 Power Surge At Top End

    Re: Early 80's Johnson 150 Power Surge At Top End Compliments of FR
  4. HighTrim

    Can I flush using a barrel

    Re: Can I flush using a barrel
  5. HighTrim

    Johson 87 150 Tachometer malfunction

    Re: Johson 87 150 Tachometer malfunction This should help. Let us know what you find. Good luck. Connections required are: Ground, 12 vdc (switched on/off from Ignition/Start Switch), AC (alternating current) from alternator (usually a Gray wire in engine harness, see schematic below). If...
  6. HighTrim

    1976 20hp. lu still leaking after installation

    Re: 1976 20hp. lu still leaking after installation You could always use something like this. Or use the attachmet from the lower unit oil fill pump. They screw in perfectly.
  7. HighTrim

    Johnson 6HP 1967-Flush kit?

    Re: Johnson 6HP 1967-Flush kit? Another option is simply a bucket such as this.
  8. HighTrim

    Johnson 6HP 1967-Flush kit?

    Re: Johnson 6HP 1967-Flush kit? Above the cavitation plate is a inlet plate held with two screws as FR stated. If you remove this plate, cut out a copy made of plain sheet metal, drill a 1/2" hole, and solder on a female garden hose connector, you will have a flushing attachment. This will work...
  9. HighTrim

    Lower Unit Fluid

    Re: Lower Unit Fluid Recommended is 80-90 outboard gear oil, it has additives to protect the lower if you have water intrusion. Always replace the washer on the vent and drain screw. That is the #1 cause of water intrusion. On the older electric shift motors, Premium Blend Type C oil is used...
  10. HighTrim

    Carbs floats for 175 Johnson

    Re: Carbs floats for 175 Johnson different carb, same idea, how the float arm (A) or float is parallel to the gasket surface (B)
  11. HighTrim

    1978 4HP cooling questions

    Re: 1978 4HP cooling questions I have found my infrared thermometer an invaluable tool for the tool box. I use it around the house as well. Something not exact but similar to this.
  12. HighTrim

    1971 Evinrude 85HP Prop and Prop Nut

    Re: 1971 Evinrude 85HP Prop and Prop Nut I use a prop wrench, such as this Tighten it until snug, if the cotter pin hole is aligned, insert pin. If not , back off until hole is present. There should be no play, so in your case insert pin at your first setting after you tightened it. Also...
  13. HighTrim

    tilt and trim help

    Re: tilt and trim help Here is an example of the solenoids with the 4 connector points. Might also be the plug going to the solenoid. Also keep the large red umbilical plug clean with electrical contact cleaner, and smear some grease around the connection surfaces of it before re installing.
  14. HighTrim

    Spark question

    Re: Spark question THis is what FR was referring to
  15. HighTrim

    Tach hook up

    Re: Tach hook up
  16. HighTrim

    Envirude 30hp tell-tale mist

    Re: Envirude 30hp tell-tale mist Exactly my thoughts JBJ. These little fold up buckets are quite handy, plus you can use them to hold ice and beer when not in use. ;)
  17. HighTrim

    115hp only 2500 rpms at wot! Help!

    Re: 115hp only 2500 rpms at wot! Help! The inline spark tester that I was referring to is very cheap, I have a few that are worth about 10 bucks each. You will use it as long as you have a boat. It is available at any auto parts store.
  18. HighTrim

    1975 Johnson 115 Tilt trim question

    Re: 1975 Johnson 115 Tilt trim question Here is how you need to wire it, let us know if you have any other questions. As you can see , the black 16 ga wire coming off the cylinder is for the trim gauge.
  19. HighTrim

    evinrude tilt and trim

    Re: evinrude tilt and trim I believe that is the 1979 3 wire motor. This should be the wiring diagram for it, supplied by Ezeke. Let me know if it is wrong.
  20. HighTrim

    Evinrude Shifting Problems

    Re: Evinrude Shifting Problems You may be able to leave in the last couple threads. What you are removing is number 49 from 54.
Top