Latest activity

What's new New posts Latest activity

M

MarioAlvaradoJunior@outlo replied to the thread Never owned a boat!.

Gas I can do that at the dock, along with potable water and the anchors and safety gear can be brought on board later while its moored...

3 minutes ago
P

poconojoe replied to the thread overheat mercruiser.

Water seems to remain in the intake manifold, even after draining everything. (2003 4.3L Mercruiser with 5 drain plugs) So, I should...

3 minutes ago
Scott Danforth replied to the thread Mercruiser 5.0 crankshaft front oil seal replacement.

I would also ditch the plastic cover for the billet aluminum front cover.

4 minutes ago
Scott Danforth replied to the thread 5.0gipefs fuel pressure regulator.

I would take this time to build a 383 if you have to pull the motor and replace rotating assemblies

5 minutes ago
WIMUSKY replied to the thread 2022 NFL - Week 5.

The Broncos paid big money amd draft picks for a has-been, he's only throwing 59% for the season... They must of took a page out of...

6 minutes ago
G
Galvez83 replied to the thread 5.0gipefs fuel pressure regulator.

It was taken apart after i changed the fuel pumps. I replaced the diaphram and the gaskets. The spring i did feel mushy. Due to the...
13 minutes ago
C

ChadMichels replied to the thread Mariner Mag II Oil Warning Module - bad?.

Yeah I did that, but I mean by checking some kind of specific voltage or resistance output on the module, which doesn't appear possible...

40 minutes ago
R

racerone replied to the thread 1964 Johnson JW-19M Restoration project.

I picked up 5 magneto plates at ---aomci---meet.-----New factory coils , points and condensers.-----I do not see an issue with the...

41 minutes ago
R

racerone replied to the thread Broken head bolt. Evinrude 150 E150EXERV..

I would make a drill jig.----Use 3/4 or 1" plate steel.----You need to make sure drill does not wander off to the side.-----

45 minutes ago
briangcc replied to the thread Never owned a boat!.

You're forgetting a few key pieces of information.... That's dry...no gas, no batteries, no safety gear, no anchors, nada, zero, zip...

47 minutes ago
C

Crosbyman replied to the thread Broken head bolt. Evinrude 150 E150EXERV..

heat soak heat soak heat soak .....try hot vinigar to loosen the calcium/salt start with a small centered drill then move up...

50 minutes ago
A

airshot replied to the thread Lawrance Elite 7 HDI sonar/ gps unit question.

Many thanks for the video !!! I was pushing so many buttons in frustration that I might have changed the transducer ....who knows. But...

58 minutes ago
R

robert graham replied to the thread 2008 Yamaha 90TLR fuel filter.

That filter is fine, but maybe you should just go ahead and install the Atwood fuel/water seperater cartridge type filter on your...

Today at 7:32 AM
M

manebeam replied to the thread Quicksilver 3000 Classic w/trailering button: Replacement options.

Lol, I'm being presumptuous here but thanks fellas for the insight! If I'm wrong I apologize :) I've looked everywhere for a direct...

Today at 6:58 AM
Q

QBhoy reacted to paulswagelock's post in the thread Mercmonitor with Like.

It is a bit old school but the most cost effective way to utilize the smartcraft data.

Today at 6:56 AM

Show older items

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Latest activity

Follow Us