Search results

  1. jakedaawg

    Prop shaft run out spec?

    I am confused maybe. You say runout. When I straighten shafts I shoot for 0.002". If you are talking just side to side or top to bottom play then I agree with dingbat.
  2. jakedaawg

    So, what did you do today?

    Nothing like mimosas on the sand bar with smoke on the meat. Abundant sunshine. Does not suck.
  3. jakedaawg

    So, what did you do today?

    The Uff Da barge is at it again. 9 racks of baby back, bunch of chicken, corn on the cob, and dish to pass. Gonna smoke em with apple wood this year. Enjoy life daily!
  4. jakedaawg

    1995 evinrude 90 hp pees at idle but doesn't when running higher rpms

    Install new impeller. May need the housing as well. Inspect that.
  5. jakedaawg

    1999 Evinrude 90 V4

    I dont think you would need to "rebuild" the carbs. Just clean them. Remove each carb. Take the bowl off. Being careful to note location remove the four orifices/jets. Each bowl has four jets. They are deep in the holes, 2 horizontal and 2 vertical. Blow carb cleaner or compressed air. If...
  6. jakedaawg

    1990 40hp evinrude

    Start at beginning. Open airgap spark test with appropriate tester. Compression test. Fuel sample.
  7. jakedaawg

    Johnson 150 VRO warning alarm

    After your compression check did you happen to hook up any wire connectors that were previously disconnected? I would guess that you saw wire connectors at vro and hooked them back up. If vro is disabled and pre mix is used the four wires from vro should be left open.
  8. jakedaawg

    System check lights off but horn on

    Yes, I think maybe a bad horn or temp sensor. Assumes you are not over heating and can rest a hand on top of the head. Is your system check guage a stand alone or integral to the tach?
  9. jakedaawg

    1990 40hp evinrude

    You need a peak reading voltmeter. Edit: I see, you mean a way to check with the motor not running. Yes, an ohm meter will say something. A better test is with a working starter motor if electric start and a peak reading voltmeter. Answer me this...what makes you ask the question? The...
  10. jakedaawg

    Which manual covers digital distributorless ignition

    Yes, perfect. Saves me digging through dusty cabinets looking for 30 year old 3 ring binders.
  11. jakedaawg

    Which manual covers digital distributorless ignition

    Thanks guys, I'll go through the service bulletins. Never dawned on me.
  12. jakedaawg

    Which manual covers digital distributorless ignition

    this set up is the one I am looking for a manual for. Book number and manual year would help a ton. Thanks. Or just whatever I have to do to set base timing. You know, like the ground this wire and connect these two colors together type thing.
  13. jakedaawg

    Which manual covers digital distributorless ignition

    I probably have 40 sets of mercruiser manuals and none have the destributorless digital ignition circa '91. Anyone know which manual I need? I have a full set from 88, full set from 92, neither have it. Either way, dressing a 3.0 L and going to have to do the timing. Including a pick of...
  14. jakedaawg

    1988 Evinrude 90 HP V4 VRO

    Step one on these is a compression test. Post results. It's just a must do 1st step
  15. jakedaawg

    Confrim my suspension

    My phone is not good enough to read those plugs for you. They would appear steam cleaned...
  16. jakedaawg

    Confrim my suspension

    Yes, you are suspended...lol, just kidding
  17. jakedaawg

    E150DCXSCR 2008 150hp

    On another note...if you just installed a new oil tank I hope you ran the winterizing function at minimum. Better yet would be to use the software and do it right. Air needs to purged. These 6 cyl models are not reliable to begin with.
  18. jakedaawg

    E150DCXSCR 2008 150hp

    Are bot the shift cable and the throttle cable installed?
  19. jakedaawg

    2003 115HP/4 Stroke - Engine Running and starter is engaging in NEUTRAL

    Would help if you looked and determined if it was the bendix...
  20. jakedaawg

    Johnson 50 in need of help!!

    Just check the carbs, if vro is hooked up the carb bowls may have filled with oil. It happens sometimes.
Top