Search results

  1. rolmops

    1957 Johnson Rd-19 35hp questions

    Next time, use marvel mystery oil or a very light hydraulic oil (gear or steering) Because now you have to get rid of the pc blaster in that bearing. Any way you should pour a little bit of gear oil to flush the bearing and remove the pc blaster. I keep on forgetting to write it down, but the...
  2. rolmops

    1957 Johnson Rd-19 35hp questions

    That is fairly simple. You would shorten it from 28 to 23 inches. You can shorten the water tube and the shift rod. That much is simple. The more complicated one would be the drive shaft. You will have to look for a short shaft drive shaft. The 57,58,59 and 60 all use the same shaft although you...
  3. rolmops

    1957 Johnson Rd-19 35hp questions

    On a side note. When you decarb the engine , make sure that the wind will move the smoke away from houses and stuff like that. It produces a wicked mean black smoke. Last time I did it, I had the cops over in my backyard because they thought I had a fire in my yard, which, by the way, proved...
  4. rolmops

    1957 Johnson Rd-19 35hp questions

    You should start with buying a Seloc manual for Johnson/Evinrude Outboards 1.5 to 40 hp.The 1956 to 1970 version. Yes a Seloc because it has everything in it that you need and it is written with the beginner in mind. I have owned 3 1957 35 horse Johnsons and apart from being very thirsty engines...
  5. rolmops

    MerCruiser 4.3L V6 engine block part identification needed

    Some carburetors have a choke system that use exhaust gas heat to choke the carb and that oval thing you see is where it connects. You can just install an electric choke on your carburetor and ignore the thing. The oval thing has the "Choke Stove" which is just a piece of tubing.It should have...
  6. rolmops

    Why is my gas orange?

    just remember to clean the tank out with soapy water afterwards. Vinegar is acidic and causes corrosion
  7. rolmops

    Why is my gas orange?

    I don't know if vinegar dissolves varnish.
  8. rolmops

    Why is my gas orange?

    Old Bill Mayer from Mayers Marina in Webster,NY, taught me that in order to really clean a metal tank, you have to pour a few quarts of lacquer thinner into the can and a few hands full of roofing nails. you shake it real good every few hours and leave this concoction about 24 hours in the tank...
  9. rolmops

    Boat age vs financing.

    Cobras have a bad reputation, which at one point held value, but at this point it is no longer deserved. There are a lot of spare parts available and a lot of servicing things are easier to do. It is nice not to have to take off the lower unit in order to check or change the impeller. Tilt/trim...
  10. rolmops

    Boat age vs financing.

    I don't understand why you would want to finance a project boat. Over the past year I sold a 1984 19 foot Islander in very good condition but sort of crappy looking for $2500 and that included a fish hawk x4 and a furuno 628 fishfinder. I was lucky to get that money because the price for these...
  11. rolmops

    Does anyone remember when car & boat engines only had.

    I remember that system on my 1943 Harley Davidson Liberator. I always had a little tool kit with spare points and plugs tied onto the sidecar. I bought it in 1973 brand new in the crate from an army over stock depot in Marocco while on a tip there. I drove it north to the Netherlands where 2...
  12. rolmops

    Lake Ontario

    Thunder storms with heavy rain and lots of lightning can form 10 miles away from you in the Lower Great Lakes area. They will come at you at 40 miles an hour and surprise you.I have actually had to run north toward Canada to escape because these storms often hug the shore line. Always top of you...
  13. rolmops

    Lake Ontario

    Any boats that lay in a slip all summer will eventually have wood rot. Boats that are trailered and kept under cover when not in use will have far less of a problem. The big exception is the Boston Whaler. Those rigs are exceptional in quality.
  14. rolmops

    Lake Ontario

    I have fished Lake Ontario weekly for the past 25 years. I started with a 17 footer which is fine for nice sunny days. From there I went up to an 18 footer. These boats usually have a much higher gunnel and lay a bit deeper in the water, next was a 19 foot Starcraft Islander and now a 22 footer...
  15. rolmops

    I am starting to believe some of the global warming in N J.

    Roscoe, with all due respect, but Lake Michigan does not have the arctic and antarctic melt off flow into it. Also the water in Lake Michigan streams out of it toward the lower lakes and finally the Ocean. On the other hand, the oceans are the final destination of water and there is no down...
  16. rolmops

    Telltale on lower unit?

    I still say not normal. If it is just a drizzle, sure, that would be normal, but when it "shoots out a steady stream" that is not normal. It would mean that the exhaust housing is full of water and that it is pressurized enough to shoot out a steady stream. That water should have flown freely...
  17. rolmops

    Telltale on lower unit?

    No this is not normal. It's not the hole that worries me. It's the water coming out. There are a few potential problems. It may be that the pipe above the impeller (partially) popped of and spouts the water around in the lower unit housing specially when your muffs are blasting full force, or...
  18. rolmops

    Nobody fishing?

    Uhh Yes. I was playing with some tuna that were under the dolphins.
  19. rolmops

    This happened today, and in the blistering heat.

    I replaced the wood in my boat with a piece of aluminum. i went to a metal store and from the leftover pile I pulled out out a 2 inch thick end piece.One inch thick would probably have been thick enough. It cost me about 5 bucks. Next I pulled the mostly rotten piece of wood out and cut a copy...
  20. rolmops

    4.3 liter 1989 Cobra problem

    I replaced the lower shift cable. It was easier than I expected. The engine end is leaving me with a question. The cable was sent with some tools. One to keep the lower end in position and one tool that is supposed to show the exact distance between the front end hole and the position of the...
Top