Search results

  1. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Go to the link I posted and check their product line. They make a Fire Resistant version. The stuff I have is general purpose. The foil is a vapor barrier. I think it will do fine. There is a similar product in the doghouse over my motorhome engine, and that 440 V8 gets HOT. The fiberglass...
  2. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    It's a 1/2" foam with heavy foil on both sides. The other side had printing on it. Got it from Lowe's. I glued it in with Power Grab construction adhesive. We'll see how it does. https://www.rmax.com/r-matte-plus-3
  3. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I'm getting close to splash time. Trying not to forget anything. I still need to gas it up, add water, run it and make any final adjustments. I also need to make sure I have all of the STUFF on board that I will need. I will probably set up my bow line and dock lines in the driveway...
  4. Reserector_

    1992 Malibu Sunsetter Euro F3 rebuild seeking advice

    Odds are that your new transom piece will be bowed a bit. Use that to your advantage when clamping/pressing into place. For example, if the center hits and the ends are bowed inward, there may be no need to clamp the middle because clamping the ends will create pressure in the middle. Or...
  5. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    iBOATS of course. ;) It's a Sierra kit # MP41400 Comes with the 200° temp switch, a 6psi oil pressure switch, and the buzzer. You have to add a T fitting for the oil switch and whatever else. You may have the wires already. Mine were bullet connectors near the temp sender and oil pressure...
  6. Reserector_

    '90 Maxum 2100SR - restoration & conversion

    It's getting fun now, isn't it?
  7. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Chipping away at my checklist. Skeggard is installed. Bimini top is installed. My boat never had an overtemp or low oil pressure alarm, but it did have the circuit in the harness. I bought a kit that had the switches and buzzer. I just needed to do the plumbing. Temp switch and buzzer...
  8. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I plan to clean up the prop, but should I leave it bare aluminum, or should I paint or coat it with something?
  9. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Last night I installed the outdrive. A little wiggling and shoving is all it took. I tossed a prop on it to complete the look and took some photos of this milestone moment. Or should I say channel marker moment? My Skeggard arrived, so I checked it against the skeg and could see that mine is...
  10. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I pulled the boat around to the garage and washed the pollen off. I made a brief walk around video while there was still daylight.
  11. Reserector_

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    No special bearing puller needed at this time. Just drive it out from the engine side. I think I drove my new one in with a slide hammer rig. Or was it a long bolt used to PULL it in? Meh. The point is that you don't exactly need special tools if the housing is off the boat.
  12. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    I've finished up the outdrive. The manual says to use nothing on the water tube gaskets, and to use gasket sealant on the two o-rings and carrier that they are on to prevent oxidation, but since mine is freshwater only, I went with a light smear of grease on all. Went together great...
  13. Reserector_

    Sealing a weathered fiberglass floor

    Carpet, perhaps?
  14. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Question that I cannot find an answer to: When mating the OMC Cobra upper to the lower, should I put anything on the o-rings and water passage seals? Everything else calls for gasket sealant, but I was thinking grease on these? It doesn't call for anything in the Seloc manual, and I can't...
  15. Reserector_

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    Matt, do an online search (images?) for merc installation drawings. That stuff is out there. I used some to figure out my front engine mount. I feel certain they would have a dimensional drawing for the opening.
  16. Reserector_

    '90 Maxum 2100SR - restoration & conversion

    I didn't glass any of it. I plan to insulate the interior with foil- backed foam board, and that's it.
  17. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Got a new aluminum anchor to try.
  18. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    The new bearings were within .001" combined, so I reinstalled the factory shims. That was good news. Pressing on...
  19. Reserector_

    '90 Maxum 2100SR - restoration & conversion

    Keep in mind that the hinge will bear much of the weight. You will never actually lift the entire weight once it is installed and hinged. Maybe half when you first start lifting, and lighter as the hinge takes more and more.
  20. Reserector_

    Building a '93 Caravelle 1750 Classic Bowrider

    Good plan, measuring and comparing the actual bearings. Data is truth. That could save me some time. Thanks for taking the time to dig that up.
Top