Search results

  1. jerryjerry05

    leaking oil.

    Looks like gear oil, probably leaking from one of two places??? The shift rod seal, or the drive shaft seal under the water pump. Drain the oil, drop the lower unit, then pressure test and using soapy water find the leak. That hole is there just for that reason, to drain excess water or unburned...
  2. jerryjerry05

    NO GO!!!!???

    2000 115 txry(?) 2 stroke. Starts great and runs all day at an idle. Give it gas and it dies. Won't rev up. Not overheating, good gas, carbs spotless, good comp all 4, good spark, fuel pump new, plugs good, linkage ok, motor seems to be in good shape, just no go. """GUESSING???"""Is it...
  3. jerryjerry05

    float setting

    Turn the carb upside down, the float should set level with the body. Turn right side up and the float should drop and almost hit the center post. Check the floats for water??
  4. jerryjerry05

    1990 Force 50 HP Bearing Cage Kit Replacement

    Pressure test before adding oil. The bucket needs to be deeper or use the right muffs.
  5. jerryjerry05

    85 hp force outboard fuel/oil mix what is

    Start another thread.
  6. jerryjerry05

    1990 Force 50 HP Bearing Cage Kit Replacement

    Bondo and white paint. They also sell a plastic keel protector(West Marine)
  7. jerryjerry05

    Super Ugly Pistons

    The port cover gaskets probably went bad and allowed more air to get in the system and created a lean condition, loose carb or gaskets somewhere in the intake side could have contributed to the problem?? An open condition on the reeds: a small amount is acceptable. Your reeds didn't cause that.
  8. jerryjerry05

    Force 85 (1985) Doesn't like to do more than idle in water - and often dies on its own

    Always include the year, model and serial# if possible. Fuel pump. ?? The factory sent out a service bulletin in the late 80's that the air screw should be set at 1 turn out and left there. BUT!! not all motors run at that setting. I found 1 1/8th turn worked great on my motors. One of my...
  9. jerryjerry05

    1990 force problems

    Sounded good to me. A no load of 5000rpm really doesn't show much. A loaded rpm would be much better, in the water, boat loaded and gassed. Then try to hit 5500 at wide open.
  10. jerryjerry05

    Tilt trim

    See next post.
  11. jerryjerry05

    Force/U S Marine 15 hp won't start

    Did you check the things I posted before? (The fuel line where it goes into the motor, that connector has a rubber seal that goes bad and allows the motor to suck air and die. Another problem might be the float in the carb isn't set right and runs itself out of fuel. When pumping the ball, does...
  12. jerryjerry05

    1989 Force 50hp spark plug options

    Amazin how the littlest things help!! You were lucky it was just a cheap coil, the stator can be 180$ or more.
  13. jerryjerry05

    87 force 85hp choke plunger

    Is the choke rod binding? Maybe someone's installed it wrong? Pics of the choke and linkage(closeup)
  14. jerryjerry05

    1991 Force 90hp starting problem

    Pic #2 of the pics you posted, there's a thick paper gasket that fits over the stud and the bottom hole. #7 in the pic I inserted.
  15. jerryjerry05

    Lost the yoke

    Take it apart and use marine assembly grease to make sure the yoke stays on the rod. Always include Year, model, serial# location and any other info that might help?
  16. jerryjerry05

    1991 Force 90hp starting problem

    What seals?
  17. jerryjerry05

    87 force 85hp choke plunger

    Does the slide go all the way in when pushed by hand? Try that and maybe spray cleaner and lube after cleaning?
  18. jerryjerry05

    Hi all so back kind of after a rebuild as found broken rings not causing any problems but once seen

    17ft. with a 125= the prop should be a 19 maybe even a 21 From what I remember????, the 17 Capri came with a 85/90 depending on the year? The 85/90 had a 17p. What year is the boat?
  19. jerryjerry05

    Tilt trim

    Just make sure the electric motors turning the pump??? Remove the electric motor and rig up a drill and turn pump and see if that makes the oil move???
  20. jerryjerry05

    Tilt trim

    Also new pump: the connector (if there is one??) between the motor and pump might not be hooked up? Or since it's new the connector might be too short or missing?? Not all have a connector.
Top