Search results

  1. j_k_bisson

    Looking for help identifing Year - BF75L 1301753

    Looking to uy a service manual for this motor that is new to me, and need to know the year of this motor. The serial number tag says BF75L 1301753 I need the manual to set the timing where the belt on top is. One of my kids pulled it off and I need to set the timing again, along with cleaning...
  2. j_k_bisson

    93 75 hp Mariner - Oil Injection disable / bypass

    Watched a couple of U-tube videos on how to by-pass the oil injection system on my 1993 75 hp Marine. All they do is disconnect they wires from the oil sender in the oil tank and remove the oil pump drive shaft. Then Plug/cap the oil lines to the fuel and oil pumps. Questions to everyone here...
  3. j_k_bisson

    Alarm - IS it bad?

    I have a 1993 Mercury 75 hp that the alarm was not sounding when I bought the boat, so started trouble shooting and removed the alarm, and tried testing it. When I make the + and - contacts to the battery directly, the alarm horn momentarily crackles once power is applied. No Buzzing sound. Does...
  4. j_k_bisson

    1993 Mariner 75 hp 3 cylinder tiller, can't find alarm under hood

    Just bought a 1993 Mariner 75 hp 3 cylinder tiller on a Lund Pro V. When I turn the keep, I do not hear any beeps or anything. I Ordered a factory service manual, but don't want to wait for it to come in. So I thought I would ask here where it could be located. I looked up online to find what I...
  5. j_k_bisson

    93 Mariner 75 hp

    Looking to get back into boating again after a couple years of doing without. I'm looking at a boat with a 75 hp Mariner 1993. I was hoping the community here couple give me some insight to this motor. Are there known issues with these motors? (read that the stators are not the greatest)...
  6. j_k_bisson

    1988 johnson v6 vro info

    Re: 1988 johnson v6 vro info I have attached what a 1987 power packs should look like. Please compare what they look like and what yours does. Notice the two independant power packs. to the left. The 1988 has only on power pack that does the function as the two separate did. Now note, this...
  7. j_k_bisson

    1987 Johnson J200TXCUC lost power

    Re: 1987 Johnson J200TXCUC lost power I would recommend to you that you cut every one of those old connectors of and redo them. While you are trying to find what is wrong that will clean up any confusion there maybe that the problem is at the switch. I have attached a pic of the wiring...
  8. j_k_bisson

    1987 Johnson J200TXCUC lost power

    Re: 1987 Johnson J200TXCUC lost power Here are some of the old water control valve replacements searches http://forums.iboats.com/johnson-evinrude-outboards/86-johnson-200-j200txcdr-control-valve-removal-561310.html...
  9. j_k_bisson

    Looking at a new truck......

    I understand that asking this question can develop into 100% opinion based bais. I am looking for facts and stories. I am looking at buys a new 2012 Chev Silverado. It has a 5.3l vortec aluminum block motor. I am a Ford guy switching to a chev. Let's not go there..... I am asking if anyone has...
  10. j_k_bisson

    Product review - Meguiars Solo products.....

    Re: Product review - Meguiars Solo products..... Here is two different pics of each side. A before and after.... As you can see. There is a definate improvement. This is only with a quick going over. Only one compound and one wool pad on a cheap Harbour Freight buffer. I will admit...
  11. j_k_bisson

    Product review - Meguiars Solo products.....

    Well do not know if this is the right section of this forum, but I thought I would post a product review of the Meguiars Solo buffing products. I hope I can and it helps others..... Meguiars Solo Wool Heavy Cutting Pad 7" - #WWHC7 - This pad works great and is very aggressive. I removes heavy...
  12. j_k_bisson

    Looking for a boat BBQ......

    Well summer is coming fast and need tyo figure out how to rig a BBQ on the 2002 WA Trophy. I have been looking at the gimbal mounted BBQ's but I was hoping to see what everyone else has. I was thinking of converting a small propane BBQ into a Gimbal mount. Seeing the BBQ is only around $30...
  13. j_k_bisson

    Yatch Dr and all other Experts, Meguires Pro unigrit sanding pad review, are they ok?

    Hey all you gel coat experts, A quick Question on sand paper for wet sanding gel coat. I picked up off Ebay som Meguires Pro Unitgrit DA sanding discs. Just wondering what you guys think about them. They are pricey normally, but I got a deal on them. When they came in today, I was reading the...
  14. j_k_bisson

    Frankenstien's revenge, 1987 junkyard 225 Evinrude jetting discussion

    Re: Frankenstien's revenge, 1987 junkyard 225 Evinrude jetting discussion I do have the plug chart. It came with the Factory service manual. Here is a pick of the plugs.... Those plugs have about 2-3 hours on them. They where ilded for 4-5 minutes before shutting down. There is some...
  15. j_k_bisson

    Frankenstien's revenge, 1987 junkyard 225 Evinrude jetting discussion

    Tried to continue in the original build thread to carry on the discussion of jetting this monster. There have been some performance issues that I was hoping to clear up. But before we get into the nitty gritty, I thought I would give a basic overview. The motor was built in thread...
  16. j_k_bisson

    Trolling questions

    Re: Trolling questions I troll Lake Erie for Walleye's all summer long. I use a kicker, 10hp Honda 4 stroke (old BF100 CDI), they have the ability to charge your batteries why you troll. So not problems with power. I still have 2 bateries and they are separate by a perko switch. I run...
  17. j_k_bisson

    1991 Force 120 HP rebuild project

    Update 11-12-2011 - Putting it in storage for a while...... Update 11-12-2011 - Putting it in storage for a while...... Thanks Frank, I have always worried about using one of those type. All I see is honing something a bit more out of taper. How much does one of those actually take off?Also I...
  18. j_k_bisson

    JL Audio is it worth it?

    Well I normally don't hang out in this area as I am not very audio literate. Actually not at all. So I start with my question andn hope to get some help on planning my new boats sound system. I have a 1991 Bayline Trophy that has a 225hp 2 stroke outboard on the stern. I want to be able to...
  19. j_k_bisson

    1991 Force 120 HP rebuild project

    Update 11-9-2011 Update 11-9-2011 Well last night I started with washing the block down. I went ahead with the gasoline wash down. And Man did that work! Wouldn't recommend it to anyone due to the safety hazards, but if you want to remove all the crap in the exhaust chamber then this is the...
  20. j_k_bisson

    1991 Force 120 HP rebuild project

    Re: Update 11-8-2011 Continued Re: Update 11-8-2011 Continued Actually I have not posted any pics of the Reed Valves. So I went and took a couple of pics and here they are. They are located in these motors right behind the carbs before the intake side of the block. Here is the cover plate...
Top