Search results

  1. W

    Evinrude 6 HP 6303SJ - 01106 Crankcase seals

    Curious about these. On the top of the drive shaft is a set of springs and seals held up by a pin. I looked them up and think they were refferred to as crankcase seal assembly. They are missing on my motor. The motor starts and runs fine. <br /><br /><br /><br /><br />What exactly do these parts...
  2. W

    Mercury 35 HP Extra Long Shaft

    <P>I have a Merc with no ID plate on it. When I puchased it it came with an owners manual which has serial # OB 177541 , Model # 90 150 22870 686 handwritten on it. Also it says Extra Long Shaft.Measured from the bracket(top of transom) to the cavitation plate is about 25"<P><br /><P>My...
  3. W

    1971 50 HP Evinrude No telltale run on muffs

    Just tried my motor Model #50173S. Ran it on muffs instead of a barrell. It ran fine and cool, never hot or warm to the touch. No water ever showed out of the exhaust pisser. However blackish water did show through the prop exhaust hub. How can I tell if the water pump is pumping when running...
  4. W

    1971 50 HP Evinrude Selectric Shift.

    Model # 50173<br /><br /><br /><br /><br />Won't go to reverse. Neutral and forward are fine. Any suggestions?<br /><br /><br /><br /><br /> Is the Selectric Shift problematic by nature?
  5. W

    Replace Water Pump Rude 6 HP 6303SJ

    Good day sirs. <br /><br /><br /><br /><br />In the old days when I worked on 50's & early 60's Evinrudes there was a small plate with two screws to remove on the mid / lower section in order to disengage the shift rod and drop the lower unit to replace the water pump. I am about to attempt to...
  6. W

    Evinrude / Merc/ Johnson run without thermostats..

    I live in Southern CA. Here and again I pick up old outboard motors and as a hobby get them running again. Often they don't pump water or show no sign of it as they have been stored for a while, turns out that often the thermostat is just stuck. Although I have replaced a few impellers I never...
  7. W

    110 HP Evinrude Power Pack CD4?

    Hope all had a great Thanksgiving. Afew days off to work on my outboard. Evinrude Mod# E110 TLCCA, 1988.Have found my Seloc manual and this forum invaluable to my amatuer outboard abilities. My 110 powerpack is not in my manual. I have tried to match the diagrams to no avail. I checked my power...
  8. W

    Evinrude 6 HP What year is it?

    Good Am. Just brought home another project,looking forward to getting her going. Would like to know the year of this motor. Evinrude 6 HP 6303SJ 01106? Thank You.
  9. W

    1988 Evinrude 110 HP

    Can anyone please furnish this information. I need a set of controls (side mount) for this engine. Which ones are compatible, will power pilot work. Are the cables the same on all OMC controls.Thanks.
  10. W

    1988 110 HP Evinrude E 110 TLCCA Compression

    What should the compression be on this motor?. The maximum and the minimum? Mine is at about 110 on all four cylinders.What is considered bad and what is considered marginal? What was the original when new?
  11. W

    1988 Evinrude 110 HP Compatable controls

    Will Power Pilot Controls and cables work on this motor. Have the control cables changed from the 70's to the 80's. I have brand new cables from a 1975 50HP Rude purchased in 1975. I now have a 1988 Rude which I need remote controls. I am willing to purchase a used Power Pilot Control with a...
  12. W

    Merc 110- What Year?- Stalls at WOT

    Hi Gentlemen, Just bought a used boat and moter. Have not had one in years.Could you please tell me the year or refer me to a site for my Merc 110 serial # 5543378.Also I used it today ,started and idled great. Opened her up and ran fine for a bit then stalled.Got her started again ran at low...
  13. W

    Float Replace? 110 Evinrude 1988

    Dropped my float and it chipped a bit while rebuilding my carbs. Does it need to be replaced? Also, when it is chipped (1/4" of surface) does that allow it to become saturated and not function by not allowing fuel into the bowl or vis versa allowing it to flood(gas coming out of carb throat)...
  14. W

    1988 Evinrude 110 HP Trim

    Can someone please share with me ? I need to adjust my trim on my Evinrude 1988 110 HP. It is on a stand not on a boat. I read in my manual how to adjust the tilt manually but it does not mention how to adjust the trim. Heres the problem. Project engine I work on when I have time. Both trim/...
  15. W

    Evinrude 1987 110 HP Compression

    Motor was given to me and has become a project . Compression is 110 and 110 on top cylinders, 100 and 80 on the lower cylinders. Can this engine be used with these readings. It starts and runs, does it have much life left in it? Might I be able to get a season or so out of it. My season is only...
  16. W

    Evinrude 1987 110HP Reed Valve Interchange

    Can any person offer me this answer. My reed valves are bad on my 1987 Evinrude 110 HP. Are there other OMC engines whose reed valves will replace mine? Is there a site which may offer this information ? Thanks.
View older results
Top