Search results

  1. S

    1984 force 125 spark issue again?

    When I bought the boat it worked for a while then lost spark, I found the cdi box to be the issue so I changed it used it twice and as I pulled up the the boat ramp the boat died again, I tried cranking when I got home and nothing would happend Is started checking dva in stator and trigger and...
  2. S

    Force clamp screw bolt thread size?

    From what I can measure is 3/4 but I don’t know the threads I had to drill it out
  3. S

    Force clamp screw bolt thread size?

    1984 force 125 1258x4a https://www.marineengine.com/parts/force-outboard-parts/125-hp-1984/1258x4a/motor-leg F474073-1 - SCREW-STERN - Replaced by -FA628073 does anyone know what size threads and bolt size this is?
  4. S

    Starter not engaging?

    I tried connecting the ground to the starter directly and still dosnt engage did the same on the older starter ? Even out of the motor I plugged the ground up to the starter and touched rhe hot let to the hot and it spins but dosnt engage
  5. S

    Starter not engaging?

    I bought a black max 135 and when I turn the starter over brand new batteries tried batteries on my truck and the 2 new batteries in my boat the starter will not engage what will cause this? Also bought a new starter thinking this may be the issue but does the same thing...
  6. S

    1984 force 125 fuel pump question?

    ok thank you!
  7. S

    1984 force 125 fuel pump question?

    I just bought the new diaphragm from amazon will be here tomorrow but i installed the other diaphragm like a month ago why would it tear on first trip
  8. S

    1984 force 125 fuel pump question?

    I installed a new fuel pump and did some other work as well and first day of running it full for 5 hours it tore again? what would cause it to tear like that? i ordered this one so it would be on one day shipping Teleflex 18-7806-1 Fuel Pump Kit
  9. S

    1984 force 125 Leaking tilt and trim?

    I replace the both cylinders and replace the pump and the valve body when i press the trim button up it just gurgles in the revisor and will not lift it up unless i help it lift then it will stay in place 100% when i press down it goes down extremely fast with no problem I made sure all...
  10. S

    1984 force 125 Leaking tilt and trim?

    honestly the guy sent me a replacement but its still not working after replacing the cylinder, when i look in the valve body fill hole its bubbling and gurgling right at the center, and pushing a bunch of air through the line
  11. S

    1984 force 125 Leaking tilt and trim?

    Yeah I can feel around the cylinder it’s full of liquid but I can still feel the little nick in it with my thumb nail When I took the cylinder all the way out the piston at the bottom was seeping out of the little hole with a ball in it and I couldn’t get it to seal properly found a use...
  12. S

    1984 force 125 Leaking tilt and trim?

    Seeping from the little hole with the ball in it
  13. S

    1984 force 125 Leaking tilt and trim?

    I took the top of the cylinder off and let it fill up and it bubbled around where the seal is so I guess that cylinder is bad
  14. S

    1984 force 125 Leaking tilt and trim?

    So I am trying to get the air out and can’t seem to get the cylinder to even move up at all and it’s the cylinder that holds the motor in the up position, but when I help lift it it will support my whole body weight but will not even attempt to move it up unless it’s just sealed that good I’ve...
  15. S

    1984 force 125 Leaking tilt and trim?

    Hey so the vB is moving the fluid fine and it trims down terrific but when i trim up nothing unless i help if go up, When i open the cylinder there was a small knick in the side wall of the cylinder, Could that stop it from going up? when its up it was holding up my body weight i left the...
  16. S

    1984 force 125 Leaking tilt and trim?

    I will check them out, I bought a new valve body as well
  17. S

    1984 force 125 Leaking tilt and trim?

  18. S

    1984 force 125 Leaking tilt and trim?

    the motor would go up and down then seemed to not want to go up at all now it spins but dosnt go up? im a little confused
  19. S

    1984 force 125 Leaking tilt and trim?

    on the bottom of the cylinder housing there was a small hole and i blocked off the inside and the outside it is just where the oring on the bottom of the sleeve sits, there was a hole from the previous owner and i cleaned it put steel reinforced epoxy in it and taped the inside so the epoxy...
  20. S

    1984 force 125 Leaking tilt and trim?

    so yeah my motor will raise up if i help it raise up and will stay up i can add my weight to it and it wont move and will trim down fast but will not go up unless i help it manually go up? i just went and helped it raise itself up when i take the weight of the motor off the cylinder it will go...
Top