Search results

  1. A

    Timing on 1986 318 Chrysler

    Hey all I have been help my friend with his new to him Marrenette as title says its a 86 with twin 318's. Starboard motor runs fine and is the counter rotating motor but the port motor is giving us some trouble. when we tighten the distributor hold down bolt the motor runs rough and eventually...
  2. A

    2001 johnson 150 ocean pro bogging down at 4400 rpm

    As stated I have a 01 johnson 150 that has a little hiccup miss at idle. runs strong thru 4400 rpm then bogs down to nothing never actually stalls then will recoup and run strong again. has all new fuel lines and water separator, also has a electric fuel primer
  3. A

    1992 Stratos 2250 here we go again

    A little update got the thru transom things all in The epoxy must have been to thick it cracked But I figure I'll grind it back a bit and add a little more epoxy. I actually epoxied the brass bushing in wet
  4. A

    1992 Stratos 2250 here we go again

    So nto the outside I sanded down to glass and added 2 layers of 1.5 oz chopped strand and 1 layer of 6 oz I hope that is enough
  5. A

    1992 Stratos 2250 here we go again

    So I figured I better finish these impact cracks. On the inside of the hull I I ground them out Then put 3 layers of 17oz and epoxy and then I filled the strake with epoxy fiberglass
  6. A

    1992 Stratos 2250 here we go again

    swiss cheesed my transom with some oversized holes And filled with epoxy pb
  7. A

    1992 Stratos 2250 here we go again

    In this area this is where the rear section of deck gets attached. It was bolt and nutted originally. I added a pbed piece of aluminum and figure I can pre drill and just use stainless screws int aluminum.
  8. A

    1992 Stratos 2250 here we go again

    ! layer of 17 oz over stiffners pbed and 1 layer of 8 oz over support for batteriessame as other side pb and 1 layer of 8oz also pbed a board to stringer and transom to attach different things and not haveing to attach to stringersbilge pump support
  9. A

    1992 Stratos 2250 here we go again

    Glued down the wood for my stiffners.
  10. A

    1992 Stratos 2250 here we go again

    And touch down Ready for trailer
  11. A

    1992 Stratos 2250 here we go again

    And time for the lidI guess to much weight for the cradle GlThank GOD I have a lift
  12. A

    1992 Stratos 2250 here we go again

    Liner is in And pbed in
  13. A

    1992 Stratos 2250 here we go again

  14. A

    1992 Stratos 2250 here we go again

    My foam should have been delivered to work., will find out later. In the mean time I pbed the bottom side of the removable fuel tank cover and 1 layer of 17 oz And the 1 layer of 17oz
  15. A

    1992 Stratos 2250 here we go again

    Started to add the stiffeners, I used some pink foam I had sitting around just to shape the glass.
  16. A

    1992 Stratos 2250 here we go again

    Drill my holes and started foam
  17. A

    1992 Stratos 2250 here we go again

    Ok so originally this was wasted spaceBut I am thinking I could keep my batteries inb here and probably other junk also. This is how it looks nowI am thinking I could run pvc thru both bulk heads so I can run the rubber hose for draining the deck storage and run a pvc to drain any water I get in...
  18. A

    1992 Stratos 2250 here we go again

    pbed the fuel tank ply in
  19. A

    1992 Stratos 2250 here we go again

    I totally understand kfc that was my hold up to last month. and the starboard side
  20. A

    1992 Stratos 2250 here we go again

    port side pbed and a few stainless screws
Top