Search results

  1. Rranger

    Spray Epoxy?.

    I plan on peanut butter and mat on corners. Going to have to suck it up and lay the mat. Been a journey getting to here..
  2. Rranger

    Spray Epoxy?.

    I changed a I/O hull to a outboard. I have my 3/8” plywood pieces for the motorwell cut and capped with 1-1/8” wooden dowel. I’m looking at matting and fibreglassing the pieces and wondering if there isn’t a easier way than cutting and applying Mat and fiberglass to encapsulate the pieces. Many...
  3. Rranger

    Using 2 different epoxy brands

    Managed to finish using the same epoxy.
  4. Rranger

    Using 2 different epoxy brands

    I am epoxying a layer of new mat on a section of floor I replaced. My question is I may run out of the epoxy I'm using and have to buy a different brand. Can I use the new brand while the first epoxy has been applied and still wet or does it need to cure first then carry on with the new epoxy?
  5. Rranger

    1993 90hp and 1994 125hp.

    The short question is will the trim tilt unit from the 1993 90hp serial 0D237792 part number 818903A1 work on the serial 0G086789 1994 125 hp part number 824051. From what I can gather the 90hp is a two wire unit same part number as units used on 1994 125 hp but a later serial number than mine...
  6. Rranger

    Cloth or not

    Poly. Used mat. One sheet on one to go. Waiting on supplies.
  7. Rranger

    Cloth or not

    Thanks racerone. I’ll stick a piece in between.
  8. Rranger

    Cloth or not

    I have two sheets of 3/4” plywood to laminate to the existing 1/2”, and 3/8” sheets already on the transom. Is cloth or mat necessary or not, between the 3/4” and the sheets already in place and then between the 3/4” sheets. Will be finishing with a couple three layers of Mat on the inside when...
  9. Rranger

    Volvo to Mercruiser

    Keep running across them. And it’s a boat I’m probably going to sell.
  10. Rranger

    Volvo to Mercruiser

    Scott much difference in performance from the old slant six to a Volvo 120B? Basically 20HP? Same 270 drive.
  11. Rranger

    OMC to Volvo Penta?

    Yes 350
  12. Rranger

    OMC to Volvo Penta?

    The end goal is a cheap OMC replacement. But that boat is not happening so no worry. Also always trying to get up to speed on compatible conversions. I’m also still contemplating my 19’ Sangster I/O conversion to Outboard with a pod.Transom needs to be repaired and beefed up. Need to confirm my...
  13. Rranger

    OMC to Volvo Penta?

    But if I’m changing exhaust manifolds and elbows its probably not worth it.
  14. Rranger

    OMC to Volvo Penta?

    Yes I know I’d have to do some glassing and change the keyhole. still throwing around ideas different boats ect.
  15. Rranger

    OMC to Volvo Penta?

    Will this OMC 350 engine bolt up to this 280 Volvo Penta drive assuming all the pieces in between are there?
  16. Rranger

    Volvo to Mercruiser

    I was thinking more the increase in horse power.
  17. Rranger

    Volvo to Mercruiser

    You don’t think it’s to big with it only having the slant six in it before?
  18. Rranger

    Volvo to Mercruiser

    Looking around at engines a rebuilt 350 target master with a 280 Volvo outdrive is available, and a overhauled 351 Windsor and 188 outdrive are available, a little to much of a leap from the Chrysler slant six and 250 Volvo outdrive? Tried finding HP’s for above.
  19. Rranger

    Volvo to Mercruiser

  20. Rranger

    Volvo to Mercruiser

    The glassing I’ve done enough of so I’m not worried about that, just cutting the keyhole correct when I’m done.
View older results
Top