Search results

  1. M

    Bearing buddies full of grease???

    Both good advice above.
  2. M

    bilge pumps

    As long as you have a live well pump and keep it running you're aerating the water as well. Post a few pictures of you holes. Your holes/drains should be the live well, bilge pump discharge above the waterline and the normal "pull or unscrew the plug" bilge drain.
  3. M

    Bilge Pump Wiring Question

    congrats, problem solved.
  4. M

    Gas fumes in cuddy

    Did you have the issue before replacing everything or did you notice the smell after? Is the tank foamed in? Get it pressure tested.
  5. M

    Bilge Pump Wiring Question

    Are you going to connect it thru a switch or full time on auto? There should be one black wire that's ground. Do you have one solid brown wire and another brown/tan/white ?
  6. M

    2001 Bayliner 175 bumper mounting location?

    Can you install a couple of these loop things? I don't know what they're called.
  7. M

    40amp vs 50amp Fuse

    what make and model charger is it?
  8. M

    primer bulb

    Remove the fuel/water seperator pour the gas in a jar to see what if anything is floating around, hopefully nothing.
  9. M

    Removing old water lines

    Just a guess, how about either goo gone or goof off?
  10. M

    Gas fumes.

    Find out if your tank is foamed in. If you have a leak and no gas in the bilge there are most likely bulkheads surrounding the tank. You said "Getting gas fumes in the center console", do you mean cabin?
  11. M

    F250BTUR Bad Rattle

    have you talked to the mechanic you bought the boat from?
  12. M

    Ballast resistor? why

    Isn't that what a condenser is for? They're just a capacitor that absorbed the rapid spike in voltage to keep the points from arcing. I'm going to read up about ballast resistors, I may as well learn something today.
  13. M

    Ballast resistor? why

    I haven't heard of a ballast resistor but to measure the value of a resistor you need to remove at least one lead from the circuit but you need to know what the value should be. Does the manual state the value of the resistor? Do you have 12v between either side of the resistor and ground...
  14. M

    2013 Yamaha 25hp 4 stroke running hot

    Start with replacing the water pump kit and check/test the thermostats. Any idea when they were changed out last? How was the stream of water from the pisser? Then track down the leak.
  15. M

    Wont crank from the key switch

    I don't have one.
  16. M

    Electronics die when cranking engine

    You said "checked prior and both of them at 12.5v Weird'. If the batteries are connected in parallel ,+ to + and - to -, or with the switch in the both position, you'll read the same voltage since you are reading them as one battery. If you have any connections that are "a bit eh and loose at...
  17. M

    Electronics die when cranking engine

    I also have two batteries but have two switches, 1 switch for accessories 1 switch to the motor. You don't want your electronics connected to your starting battery, they're turning off because of the voltage drop when you're starting your motor.
  18. M

    IS 427 A - freon sold in small cylinder like auto 134a replaces R 22

    check on ebay or grainger.
  19. M

    1st Boat/First Thread/First Everything lol. Need help

    " Approach a dock or landing only at the speed which you are willing to hit it." So true tpenfield. I use windy.com & noaa for weather. I have a mental check list from the time I connect the trailer to my truck until I get home and disconnect it. Make a written list until you get the hang of...
  20. M

    Starting Problem

    If you have a jumper cable connect one end to the pos of the battery then touch the other end to the starter and see what happens.
Top