Search results

  1. C

    Fault codes for 2006 Mercruiser

    Driving out of state tomorrow to look at a 2006 Sea Ray 290 SS with twin 5.0 Mercs. I am familiar with using the paperclip jumper and diode to get codes from a 1998 motor, wondering if I can do the same with a 2006 motor? One of the serial numbers is OW381653 Thanks
  2. C

    Crazy noise I cant figue out

    Newer to me 1998 SeaRay 290 Sundancer with twin 350 EFI/ Alpha drives. When trying to get up on plane a dashboard buzzer sounds but goes away when on plane. At first I thought it was related to the vacuflush toilet that is located just forward of the helm. Buddy went down to the head area...
  3. C

    Adding a Windlass....... wiring questions

    Getting ready to install a windlass on my 1998 Sea Ray 290 Sundancer that never had a windlass. Going with Lewmar V700G I intend to use 6AWG wire for the power to the motor and a contactor solenoid to control it via low voltage switch at the helm and foot pedals at the bow. My layout is: Rear...
  4. C

    Best way to deal with this miswiring

    New to me 1998 Sea Ray 290DA with twins. Trim tabs are wired backwards and up side down. When calling for up tab on port side the SB will go down. I loosened the panel to get at the wires, figuring I would be able to just move some wires around thinking there would only be a max of 3 wires to...
  5. C

    Best way to repaint the gimble ring assembly?

    Is it advisable to remove this gimble ring assembly to clean/strip to repaint, or is that just a can of worms that is not worth the potential problems? Fresh water boat.
  6. C

    Which prop to buy?

    I have a new to me 1998 SeaRay 290 DA with twin 5.7 EFI/ Alpha drives, 1.47 ratio. Original Vengeance 14x19 3 blade SS props need to be replace due to damage. I'm wondering if 20 years after original Mfg chose these props, if there isn't a better choice out there? I would prefer to use...
  7. C

    Thoughts on quality of SEI gaskets and bellows kits?

    I am getting ready to order two new Alpha knock offs from SEI for my new to me boat. Will need shift kit, bellows kits, gaskets etc. Wondering if anybody has good or bad results with these type of parts from them.
  8. C

    Now I'ive done it

    As some of you may know, I've been disassembling my two Alpha 1 Gen 2 drives with the intent of cleaning them up and repainting them this winter, Got everything apart, only problem left is the brass nut that is seated in the bell housing for the shift cable. I cut the cable down enough to fit a...
  9. C

    Thrust washer wear

    Alpha1 gen 2 Took both drives off, one of the thrust washers has significant wear on the back side, the other has none. Is this an indication of something bad?
  10. C

    This seems very odd to me

    Dealing with my first drive removal, strip down and repaint. 1998 Alpha 1 Gen 2 ​I can't figure out why there is a clip on the end of the bellows (see pic) I assume its to provide an electrical contact from the bell housing, through the wire in the bellows. It seems to me that this clip will...
  11. C

    What size bolt head is this?

    Trying to get this zinc off and cant get to the bolt holding it on. I can't believe I am even having to ask this as I've done this before a few years ago on a similar drive. I have tried both deepwell 7/16 and 1/2".....9/16 wont fit down the hole. What am I missing?
  12. C

    How do I get this anode out?

    How do I get this zinc off? I have removed the 2 set screws and its loose but rusty washer like thing where the prop seats against doesn't easily come off of the spindle?
  13. C

    Are these U joints toast?

    Found water inside the U joint bellows when taking off this Alpha 1 gen 2 drive. Appears to be only surface rust on the joints as they seem to function well but this is the first time I've gone this deep into a drive.
  14. C

    Any suggestions on how to get this bolt out

    Top of a1998 Alpha1 gen 2 drive. I have been able to get it about 1/4 way out but it feels like it is going to sheer off if I give it anymore leverage. I have shot it with some PB blaster several times, screwed it back in a few turns then back out, even heated the housing around the bolt with...
  15. C

    Water in gimbal bellow, now what?

    Pulled both drives off and found water in both gimbal bellows, which I was surprised about as the bellows themselves look almost new. I am trying to take off the bell housing so I can have the drives and housing stripped and painted this winter. I have successfully removed the hitch pin bolts...
  16. C

    Are these an automatic replace?

    Just bought a 1998 Sea Ray 290 Sundancer ​Everything except the out drives and props are in amazing like new condition. This was supposedly a freshwater all its life boat, but looking at the drives, I wonder. I have ordered an alignment tool and plan to pull the drives as soon as it arrives to...
  17. C

    Gear ratio of these outdrives?

    Can anyone confirm for me what the ratios are of these Alpha drives? Thinking of replacing them with SEI versions as they look pretty bad. ​OL100186 ​OL102986
  18. C

    Neither out drive lowering

    Just bought a new to me 1998 290 sundancer with twin 350 EFI/ Alpha drives ​I read an earlier thread that sometimes when the end caps get bad the drives can stick at the top, and they are defiantly at the very top right now. Funny thing is I don't even hear the pump doing anything. It has a...
  19. C

    How concerned would you be to buy a boat after being told this?

    Looking at a 1995 34' Chris Craft Crowne cruiser with twin carbed 350 SBC with V drives. ​Seller claims he has owned the boat for last 20 years and has never replaced anything major on the engines (manifolds, risers, starters, water pump, fuel pump etc) or drives. Great lakes fresh water all...
  20. C

    Found this was just vinyl taped while cleaning the engine up

    Plastic 90 degree elbow that comes off the side of the air cleaner/flame arrester cracked. Can this small part be easily replaced or is it part of an assembly. I couldn't find the area of the website were you enter the engine number and it provides exploded views. OL035657 1999 454 Mag MPI...
Top