Search results

  1. Baylinerchuck

    Rotten 1982 Beachcraft

    Really nice glassing there.
  2. Baylinerchuck

    Water in bilge? Bilge pump runs too often.

    When I said drill down, I mean investigate further, not literally get a drill and……well, you know. Glad you’re getting the bore scope. That’s a handy tool. As far as entrances for water, the whole outdrive is an entrance for water. There’s lots of things it could be.
  3. Baylinerchuck

    1979 Glastron Carlson CV-23 restoration

    Pictures….. we like boat porn!!
  4. Baylinerchuck

    1981 Citation Marquis restoration...

    Doesn’t matter. Doesn’t have to be pretty, just has to be. Brace as close to where the cap meets the hull as you can. Don’t over think it. The goal is to keep the hull rigid when you take off the cap
  5. Baylinerchuck

    Water in bilge? Bilge pump runs too often.

    The seawater intake tube is lower than your leak. It’s also pressurized by the water pump in the outdrive. If it was leaking water would be spraying everywhere when the boat was running. I reread your original post. You have through the hull exhaust, it doesn’t appear in the video that your...
  6. Baylinerchuck

    Suggestions for fiberglass repair along the keel

    If the keel could get dinged from time to time I recommend a KeelGuard. Once you cover the damaged area with filler, you don’t have to be as particular with finishing if you slap a KeelGuard on it. I put them on both my boats and they work well.
  7. Baylinerchuck

    Keel damaged

    Looks like a lot of beaching was done. Had the same issue with the Chaparral. It was a lake boat and beached all the time on sandbars by the PO. After fixing the gelcoat on mine, I added a Keelguard to protect it. Small investment for some added protection. Especially since I boat in rivers and...
  8. Baylinerchuck

    Rotten 1982 Beachcraft

    True. We spend a great deal of time in the summer on the Chaparral I restored. The memories are worth the rebuild pain. Ha ha.
  9. Baylinerchuck

    Polyester resin cracked while curing

    Using the disposable pastry piping bags is a great way to dispense thickened resin. You can put it right where you need it, then smooth it out.
  10. Baylinerchuck

    Water in bilge? Bilge pump runs too often.

    It’s really hard to tell from the video and since water will travel along cables, shafts, wiring, etc it can be hard to pinpoint. I had a tough time finding a pesky leak in the transom on mine after I restored it. I had to use a bore scope to find it. One of my transom plate bolts wasn’t sealing...
  11. Baylinerchuck

    Rehab SportCraft 222 1983 deep V hull cuddy walkaround

    Just got all caught up again Kev. You gonna splash this thing or what? Heck I might drive out just to see it!! Lol.
  12. Baylinerchuck

    Vintage outboard repair help?

    Not sure if you already posted, but you might want to ask your question in the Johnson/Evinrude outboard section of the forum. You’ll get a much better response over there. Chuck.
  13. Baylinerchuck

    Polyester resin cracked while curing

    I too had the same problem when I started my project. I did a little research and learned that adding 1/4” chop strands into the Thickened resin ALWAYS prevented cracking. Polyester resin without reinforcement is extremely weak. It makes a great clue, but can crack if too thick. Thickened resin...
  14. Baylinerchuck

    Rotten 1982 Beachcraft

    I like it. Nice carpentry work.
  15. Baylinerchuck

    1972 Checkmate MX-15 Rebuild

    Looking good sir!!
  16. Baylinerchuck

    1981 Citation Marquis restoration...

    Yep, that’s as high as they can go. The idea is to keep the edge the cap fastens to the same shape as the cap. However you can brace it to keep it from moving is the right way. Whether it’s 5 braces or 20 braces, if it doesn’t move, job well done.
  17. Baylinerchuck

    1981 Citation Marquis restoration...

    I would go as close to where the cap meets the hull as possible unless you already have holes in that area.
  18. Baylinerchuck

    1981 Citation Marquis restoration...

    Yep, in the middle where you have the braces now should work well. I wouldn’t worry about the middle hole, I would go more up toward the bow in a couple places. 4 or 5 braces would be pretty good, plus the boat sitting on the trailer. I put 2x6 boards between the hull and the rollers for more...
  19. Baylinerchuck

    1979 Glastron Carlson CV-23 restoration

    Man!!! I would love to have all that space, and a couple planes to boot. Envious for sure.
  20. Baylinerchuck

    1981 Citation Marquis restoration...

    Cradles on the outside are the way to go. I simply used some dimensional lumber between the rollers and the hull to help spread the load some. The idea is to keep the hull from flexing. Once you add structure after the hull flexes, it becomes impossible to get the cap to fit. Your method of...
Top