Search results

  1. S

    illuminated toggle switches

    im Looking To Replace 11 Existing Tovgle Switches With Light Up Tip Switches. The Box Says 20A At 12V. Is This The Max Load The Contacts Can Handle At 12V? I Dont Want To Unnecessarily Drain My Battery, Should I Be Concerned?
  2. S

    Replacement Ignition Switch

    I accidentally broke my old ignition and I need to replace it but I am unsure what kind I need. Bought the boat last year and I am not exactly sure where every single wire goes, there is a ton of wires under the dashboard. All I know about this ignoition is that it is wired to 12V (of course)...
  3. S

    brass plated screws?????????

    I have noticed that some screws, nuts, etc. are brass plated - or plated with something that appears to be brass. I bought a small screw for my magneto assembly. They actually sent me a bolt - I can't use this. I found a solid brass screw at a hardware store that will work. Can I use this...
  4. S

    Need a Part #!!!

    I have a 1982 Johnson 25hp w/ Controls. I need a part number for the connector that holds the throttle cable to the throttle on the motor. I have the part that secures the cable to the motor housing. I need the one that connects the throttle to the tip of the control cable. Thank You
  5. S

    johnson carburetors

    I have a 1982 Johnson 25hp (j25elcne). Someone told me that I can put a 35hp carburetor on it and the motor will perform like a 35hp motor. Is this true?
  6. S

    Breaking in my rebuild

    Just rebuilt a 1982 Johnson 25hp (my first one and it turned out beautifully) From doing a bit of research I understand that this is a good break-in procedure: During first 10 hours of operation: Pre and Post operation check ALWAYS Check for fuel, oil, and water leaks Check...
  7. S

    paint ???

    Wrapping up my first complete overhaul (going great btw). The paint on the powerhead was in terrible condition so I completely sanded it down to the aluminum. I have self-etching primer and all of the essentials for the paint job. I ordered a new head for the motor and the paint on it is in...
  8. S

    Cant find part on diagram

    I simply cannot find this part... Ill explain and hopefully someone out there will able to give me the part #. I have a J25ELCNE (1982). I am looking for the part that holds the hose that comes out of the water jacket to the cover. It is a plug or clip-like device. I believe that the part is...
  9. S

    Johnson Restoration Project

    This is my first rebuild (82' J 25hp). I completely disassembled the power head and cleaned it thoroughly. All mechanical parts are in check, replacement parts are on the way, and I have a couple questions.. 1) What is a good gasket sealer to use? In addition, there is no gasket between that...
  10. S

    hmm.. donno what tool i need???

    I have a 1982 Johnson 25hp. I am trying to remove the nuts that hold the powerhead to the lower cover/exhaust housing. The nuts are positioned beneath the powerhead, one on each side. There is little clearance from the top of the bolt to the powerhead and it is very tight. I cannot use a...
  11. S

    removing the cylinder head

    I took all of the bolts out. The head is still held in place by the gasket and sealer. I cannot pull it off by hand and I want to make sure I do this right. The last thing I want to do is damage the powerhead. Can someone provide me with the proper technique?
  12. S

    cleaning solution

    Looking for a good cleaning solution to use in my overhaul.
  13. S

    1982 Johnson 25hp -???

    Ok, I finally got my motor to run today for the first time. I have a couple concerns: Im not too sure how long it has been since the motor ran last and it got pretty smokey in my garage today. (not anything out of the ordinary, but today it was because of the motor, lol) It was exhausting...
  14. S

    1982 Johnson 25hp - NEED EXPERT ADVICE

    When I turn my ignition key the motor runs for a few seconds, backfires, then stalls out. I know that this is a fuel delivery issue but I am not sure where the problem exists. This is what I do know: 1) Only 1 cylinder is running. While servicing the motor I accidentally broke a wire in the...
  15. S

    Fuel Delivery Issue

    Not getting fuel to my 1982 Johnson. When I squeeze the bulk in the gas line it does not become firm. Rather gas leaks from the fuel pump. The fuel pump it pretty basic from that I can tell (http://www.boats.net/parts/search/BRP/JOHNSON/1982/J25ELCNE%201982/FUEL%20PUMP/parts.html) Am I right...
  16. S

    coil assembly

    I have a 1982 25hp Johnson. While servicing it I accidentally broke a wire that connected to the coil assembly. If you are aware of how the wire is connected to it then u will understand my problem. It is not a screw type connection, but rather the wire is molded into the plastic itself. This...
  17. S

    82 Johnson - No Combustion

    I have an 82 Johnson 25hp w/ electric start. I am getting spark in both cylinders but no combustion. I sprayed fuel down the throat of the carb and still nothing happened. The flywheel spins but there is not combustion. Electric problem? or fuel delivery problem??
  18. S

    ELECTRIC START - looking for expert feedback

    I have a J25ELCNE and I am having problems starting it up. When I initially tried to start the motor nothing happened. I figured that there was either a problem with the wiring, or the starter was bad. I immediately ran a voltmeter over the battery and it read 12V - good. So I removed the...
  19. S

    no spark

    I recently acquired a j25elcne and I've been fixing it up. I replaced any wires with bad insulation but not every single wire. When I tried to start the motor the starter ticked, and the pinion twitched, but it did not pop up to meet the flywheel. So I pulled a spark plug out, tried to start...
  20. S

    help with fuel mixture

    Model: J25ELCNE Year: 1982 ...obviously a 25 hp Johnson I am fairly sure it might be 50:1 but not positive, can anyone help??
Top