Search results

  1. B

    1995 Yamaha 130 oil injection lroblem

    Black to the switch. Black/red from the switch. From the blue connector. Notice that at a junction point with the engine harness the B/R turns to green/black. G/B to the oil control module and G/B to the oil connector (#25). The switch referred to is within the sensor switch assembly located...
  2. B

    yamaha 250 electrical steering

    A complete model identity will help.
  3. B

    35 HP - Never had Charging even though it's electric Start? Is this possible??

    Go to the Mercury Marine parts catalog https://www.mercurymarine.com/en/us/parts-and-accessories/parts-catalog?gclid=CjwKCAjwpKveBRAwEiwAo4Pqm6JIrzner3CFcr-0DidW_n0WQYnRdOVfmu02gJDFF3ONGayJbxAydhoCahcQAvD_BwE and enter the serial number into the search box. It will take you to where you have...
  4. B

    1995 Yamaha 130 oil injection lroblem

    The yellow light is telling you that the remote tank in the boat is low on oil. Or the oil control unit thinks that it is low. When there is sufficient oil in the tank a sensor switch closes due to a float in the tank rising. In which case a ground goes from through the switch and on to the oil...
  5. B

    F150 Engine Alarm/Buzzer

    No to the wiring being installed. With a Yamaha temperature gauge and temperature sender the sender has the wire attached to run to the Yamaha gauge. I have no idea what the Faria temperature gauge and sender consist of. Yamaha does not offer either a mechanical or an electrical oil pressure...
  6. B

    F150 Engine Alarm/Buzzer

    You will need to craft a T fitting so as to get oil pressure to an oil pressure sender.
  7. B

    2003 Yamaha Outboard oil injection adjustment

    What's a service manual?
  8. B

    Mariner 40ELO 6E9-451908 blows fuse after starting

    There are numerous connection points within the circuit from the lighting coil to the rectifier and on to the battery. Or from the battery through the fuse and on the start switch. Presumption being that your motor is wired similar to its Yamaha equivalent. Start by disconnecting wires as...
  9. B

    2003 Yamaha Outboard oil injection adjustment

    Have you any idea as to the model of the motor? Is it a 25TLR, a Z300, or something in between?
  10. B

    Mariner 40ELO 6E9-451908 blows fuse after starting

    So you do or do not have a Yamaha manual for the motor? Manual by Yamaha. Not some aftermarket stuff.
  11. B

    Mariner 40ELO 6E9-451908 blows fuse after starting

    Look at the main wire harness up near the connector at the front of the motor. Is there a label with the part number on it?
  12. B

    Mariner 40ELO 6E9-451908 blows fuse after starting

    Why do you suspect the CDI box as being part of the problem? What is the LIT number of your Yamaha manual? Is it LIT-18616-00-45?
  13. B

    2019 F25 Yamaha over heat light coming on.

    Some Yams having a tiller handle have a warning buzzer in the tiller handle itself. I do not see a buzzer in your tiller handle. Seems that you get a warning light only. Plus RPM reduction mode which should give you an indication of the motor having a problem.
  14. B

    2019 F25 Yamaha over heat light coming on.

    Some Yams are sensitive with respect to water pump parts. One can take a gamble by using aftermarket parts and/or by changing just the impeller itself. If your problem started after you only installed the aftermarket impeller I would first try a Yamaha impeller and if the problem does not go...
  15. B

    2019 F25 Yamaha over heat light coming on.

    Yamaha uses both thermoswitches and thermosensors (sometimes both) in different motor models. A thermoswitch is normally open. (What Yamaha calls "off"). At some point it will close at a certain temperature. (What Yamaha calls "on"). When the switch closes the alarm will sound. A thermosensor...
Top