Search results

  1. Dukedog

    85 merc 200 black max overheat alert

    there's your answer.. or wire somewhere? disconnect tha sensor at term on motor and test.. by that i mean turn tha key..
  2. Dukedog

    85 merc 200 black max overheat alert

    how long, after start, does it take for tha alarm to sound?
  3. Dukedog

    200 black max.

    agree with faz.. but tha '91 is probably gonna be a 2.5 steel sleeve motor.. some (most) of tha power head parts are gonna be a little different compared to tha other two....
  4. Dukedog

    Mercury 2 cycle alarm

    beep, beep, beep, beep, beep OR beeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeep? do you know tha difference?
  5. Dukedog

    1991 mercury 150 outboard black max

    first of all, "why did you get (decide ta work on it) into tha motor ta start with???".. when you rebuilt tha carbs were new gaskets used throughout including new accel. pump parts?.. was a link n sycn and timing done?... does it help if primer bulb is pumped when trying ta keep it running...
  6. Dukedog

    My 1997 150hp rebuild

    reed plate has got to be removed... you have 8 3/8" down tha middle each side of main bearings.. 10 5/16", three on each outside edge, 4 holding top bearing cap. 4 1/4" holding bottom bearing cap.. sometimes you need a mallet to "tap" it in a few places ta get it to break loose
  7. Dukedog

    150 two stroke black max

    '88 2 liter 150.. thats a "zero" not an O.
  8. Dukedog

    1991 Mercury XR4 low rpms at WOT

    start point.. boat level, motor level... center of prop shaft 3 1/2 inches below pad....
  9. Dukedog

    Mercury 175 EFI Boggs down under load

    send me an email addy and i'll send ya an OEM manual (pdf)..... your motor should have tha water cooled rec/reg?.. i may not have tha test for it?
  10. Dukedog

    Mercury 175 EFI Boggs down under load

    swap switch box leads from 1 with either 3 or 5.. see if fire fire pattern follows? sounds like a coupla switch boxes are in ya future.. maybe stator also.. wouldn't worry 'bout plugs.. i can say i've never had a surface gap plug go bad with any merc...
  11. Dukedog

    Mercury 175 EFI Boggs down under load

    do ya have access to another gauge?.. 90 lbs is tired/low.. how are ya testin' comp?
  12. Dukedog

    1991 Mercury XR4 low rpms at WOT

    1.87 gear? has it been changed?
  13. Dukedog

    Mercury 135 Blackmax

    something is wrong with middle carb.. tha feed for carbs go through each carb from top to bottom.. if its before carbs it would effect all three..
  14. Dukedog

    Serial number not showing up

    is Crowly Marine NOT a dealer???.. pretty sure tha numbers were into tha "B's" by '85........
  15. Dukedog

    Serial number not showing up

    serial number 0A104245 shows this as a 1980 yamaha built merc/mariner on this site.. https://www.crowleymarine.com/mercury-outboard/275.cfmshows this
  16. Dukedog

    Stator?

    something ta consider with tha new reg/rectifiers if they have tha bullet connectors... best if you cut those off, solder and heat shrink tha joints.. tha bullet type are known for a heat problem........... jmo.
  17. Dukedog

    No fuel Seen- 94' Black Max

    anytime you disassemble anything/part fuel related it needs NEW gaskets no mater what they look (still good or bad) they need ta be replaced with new... tha enrichner has no bearing on pressure.. yours is mounted right.. lines on top......... manual sent... let me know if you get it.
  18. Dukedog

    No fuel Seen- 94' Black Max

    send me an email addy and i'll send you an OEM manual in pdf.. tha seloc is jus good enough ta get ya in trouble.....
  19. Dukedog

    Water temperature coming out of the pee hole now what I'll do here

    yeah, tha only carbureted 2.5 150 is tha XR6... on the starboard head right below tha top spark plug (no. one cyl) there is a sensor. should be a tan/blue wire (probably ina plastic sleeve) coming from it going to a terminial with a coupla other tan/blues.. take a short (or long) jumper with...
Top