Search results

  1. Dukedog

    Mercury XR2 150 stuggling to get on plane.

    $$ wise?.. its 2.0 motor.. ya may be able ta jus have a boring done on those two holes.. probably tha cheapest wat out............ jmo
  2. Dukedog

    What are these parts on mercury 150xr2

    correct, tha bigger one is tha oiler module but tha smaller one is tha 16 amp regulator
  3. Dukedog

    Mercury XR2 150 stuggling to get on plane.

    thats a tell tale for fuel delivery.. possible justa the bulb but probably gonna be tha mech pump........ jmo.
  4. Dukedog

    Identify This Merc

    understand but tha "kits" are no longer available at any sight i've pulled up.... you might enter tha tillotson number on ebay and see what pops up....
  5. Dukedog

    Identify This Merc

    https://www.crowleymarine.com/mercury/oem-parts/outboard/1983/-1025223?q=1025223 looks like ya may be outta luck for tha tillotson............ pro marine doesn't show one either.
  6. Dukedog

    Idle Stabilizer bullet connectors discolored

    thats good but still needs ta be on tha water pushin' a load ta get idle it where ya like it.......
  7. Dukedog

    Idle Stabilizer bullet connectors discolored

    actually whatever it takes for it ta run in tha driveway but ta get it right ya need ta reset idle timing (10/32 screw on timing arm) in gear, in tha lake ta whatever speed/rpm makes you and tha motor happy.... timing numbers do not mater except for MAX TIMING number.... set it at 22* after ya...
  8. Dukedog

    Idle Stabilizer bullet connectors discolored

    sorry ta hear that.. glad ya healin' up though!!! tha white/black should make a joint in tha plastic sheath before it gets to tha module.. it will connect tha other switch box.. jus make a short jumper outta tha white/black to connect tha two switch boxes.. remove tha red/white and chunk tha...
  9. Dukedog

    Flywheel Magnets

    jus when ya think ya have justa 'bout heard/seen it all...... have no clue on how ta cut it or if it will even work... let us know how it works out for ya please......
  10. Dukedog

    Gear oil leak from water intake

    This above............ if you do change tha shaft shaft seal jus be careful to take care that you do not let tha shaft rise when you pull tha seal... prop shaft seals won't have anything ta do with leaking at intakes but will allow water ta enter tha case.....
  11. Dukedog

    1984 mercury bleed lines

    .............................................
  12. Dukedog

    1984 mercury bleed lines

    think tha one in my link is 90-97658.. its in tha link if ya can get it opened on a lap top by copy n paste tha address........ you can jus block 'em off and it will run.. won't hurt a thing.. it will jus load up at idle but should clear up with throttle added........... make sure tha motor is...
  13. Dukedog

    1984 mercury bleed lines

    copy and paste this address..... ya gotta rotate it! file:///C:/Users/allys/Downloads/Old%20Downloads/vert.%20bleed%20lines.pdf
  14. Dukedog

    Which gasket??Can anyone Tell me what part I need to replace from this video

    looks like more "divider" than power head ta me.. could be power head maybe?..to much water..
  15. Dukedog

    Which gasket??Can anyone Tell me what part I need to replace from this video

    don't forget #3 (tubing, seal).... also check both pieces for any cracks while ya have 'em off............... also if any of tha exhaust ports are really clean ya may need ta take a closer looks at tha pistons and cylinders.........
  16. Dukedog

    Please help trying to check timing

    remove all and leave all tha plugs on their wires then ground tha plugs to tha block.. even number one.. there is a "chance" (not written in stone but) of wipin' out a switch box with ungrounded coils when crankin'.. if it turns over to fast and starter kicks out to early put one at a time back...
  17. Dukedog

    Question about control cable and water separator for carbureted engine

    its ok..............
  18. Dukedog

    Question about control cable and water separator for carbureted engine

    probably was a "quick connect" on tha motor and they jus eliminated it and went straight to tha fuel pump..... losta folks do that. a filter, of any kind, doesn't have any reflection on tha "prime/choke" circuit...........
  19. Dukedog

    1985 Mercury Black Max 150 V6 Water Pump and Base unit

    any that age are if original gearcase.. those two listed are tha only ones made for for tha 2.0, 2.4, 2.5 production V6 merc..
  20. Dukedog

    What could have caused this to happen?

    bullet connectors are notorious for over heating when under a constant load....
Top