Search results

  1. SHOKENRYU

    How to remove stainless pin from OMC control cable

    I have the same questions and this looks like a good idea. Thank you for figuring it out. I have an old simplex cable that fits my 77 35hp evinrude but my new cable and control has that stainless pin that I need to remove to be able to slide my simplex end on. This could do the trick.
  2. SHOKENRYU

    glasspar lido

    Do you know the average hight from bow to the waterline?
  3. SHOKENRYU

    Driveshaft not seating into the gear box. Please help.

    Omg. Just found the problem. Impeller key fell in there. Thank you everyone. And thanks you Mat!! He asked me to check in the hole and there ut was. I am so dumb 🤣
  4. SHOKENRYU

    Driveshaft not seating into the gear box. Please help.

    Vent screw us open. I've drain the oil.
  5. SHOKENRYU

    Driveshaft not seating into the gear box. Please help.

    Will not go in all the way.
  6. SHOKENRYU

    Driveshaft not seating into the gear box. Please help.

    The drive shaft to the motor isn't the problem. Its the gear case side from the impeller. It will not seat all the way into the gear case. Still have a half inch from fully seated. My propeller shaft will not spin the drive shaft because the driveshaft isn't seated all the way in to be engaged.
  7. SHOKENRYU

    Driveshaft not seating into the gear box. Please help.

    Was changing my water pump impeller and my drive shaft came out from the gearcase. Now it will not seat completely. Still a half inch gap from the gearcase and will not slide in even wen I spin the prop. Please help. 1978 evinrude 35hp 35853R
  8. SHOKENRYU

    Johnson steering and control.

    Thank you. I'll make a few calls then. For the steering I guess I can do the wire version but for the throttle controls, I may need their assistant. Thanks again.
  9. SHOKENRYU

    Johnson steering and control.

    I wish to be able to control my steering, throttle and gear selecting for my 1993 Johnson J10RETM 9.9hp Outboard Motor. Is there a kit that is made for my year and modle?
  10. SHOKENRYU

    Need a thermoatat with seals

    The water was replaced soon after that testing trial . Impeller are new and yes I've retested the motor in a deeper tank( clean recycling bin) in deep water. I've taken the lower end off and flush the water tube from the bottom up. Water flows through the thermostat and the pee hole. I've...
  11. SHOKENRYU

    Need a thermoatat with seals

    I've just found out they sell them only in pieces 😭 https://www.crowleymarine.com/johnson-evinrude/parts/48805.cfm
  12. SHOKENRYU

    Need a thermoatat with seals

    Turns out I have no thermostat installed. Might explained why my motor is not peeing. I cannot find a complete, assembled thermostat for my 1993 Johnson Outboards 9.9 [ J10RETM]? All I've found was bits and pieces from Crowley. Can anybody help me find a completely assembled thermostat please?
  13. SHOKENRYU

    1994 9.9hp Evinrude sparks

    How are you able to reach the bottom bolt? I cannot get anything down there 1993 9.9 jhonson. I am tempted to cut a hole to gain access to that bolt 😪
  14. SHOKENRYU

    Need a thermoatat with seals

    Oh man! Lol never thought of that. I'll just use the muffs instead 😅
  15. SHOKENRYU

    Need a thermoatat with seals

    Thanks for pointing me to the right direction! My curiosity has gotten the best of me and I opened up the thermostat housing above the spark plug area. Low and behold it was bone dry and a heap of dirt and dust. I blew air through the tail tale and was able to feel air. Plugging the thermostat...
  16. SHOKENRYU

    Need a thermoatat with seals

    1993 Johnson 9.9 hp J10RETM Water pump was just replaced. It was pumping out a strong stream then stopped. Ive check the flush screw and it is bone dry. Leading me to belive it is the thermostat stuck closed. I don't want to open it until I can get a replacement seal. Where can I find a...
  17. SHOKENRYU

    Model Tag Missing - How Do I Determine Model/Yr?

    I too are having issue finding my year modle number. I found the quater size silver tab on the side g3658056. Johnson 9.9 I am thinking 1992+
Top