Search results

  1. C

    Impeller

    Gee, scrub it with a brush or use it more often. Using the boat will tend to keep the gearcase clean.
  2. C

    Tide Tamer Boat Lifts

    I have a single piling 1500# aluminum lift made by Tide Tamer. I have it loaded to capacity, or nearly. The bracket bolted to the piling tends to twist. Also, I needed the have the largest dia piling I could, jetted and pounded to have enough support. Everything else worked OK, but I...
  3. C

    Starter?

    I was working from memory. I had a 1988 4.3LX V6 MerCruiser, which I sold in 2006, so it has been a while. I replaced the starter and slave solenoid on that motor and seem to remember that the power wires plus the orange alternator wires were all on the positive battery post of the starter...
  4. C

    1996 wave venture 1100

    How about a "skake-shake" siphon?
  5. C

    Manual fuel pump restrictions?

    I presume the fuel tank is 2' lower than the engine? That seems unusual. I would expect the tank to be no more than 1 foot lower as most sterndrive boats have the engine sitting on 4-6" stringers molded to the bottom of the hull. Most fuel tanks sit on the base of the hull as well. I would...
  6. C

    Starter?

    Rick, dashboards are normally powered from both the ign key and a direct connection to the battery. The ign key powers the gauges and the direct connection, everything else. Since you are having trouble with your starting circuit, after your dashboard electrical repair I would recommend you...
  7. C

    Testing for DC based ground leaks

    DC Ground Leak? We just called it a passive drain or short. I am not sure about new boats, but newer cars often have small current flows when everything is off, especially when the battery is first connected. It would not surprise me if boats start to have those as well.
  8. C

    86-87 Mariner 150 questions

    Change as many parts as you can. I think the carrier was to hard to get out, and didn't look worn, so I left it original. I run a 16 foot (about 1000# with motor and gas) speedboat with that motor. She will swing a 23P prop, but the hole shot is a bit sluggish. She would probably swing a...
  9. C

    86-87 Mariner 150 questions

    That is a lot of pitch for that boat/motor combo. A 21"P prop would probably be max. The poppit controls cooling at high speed. If that is where she is overheating, it is a possible candidate. Make sure you get the exact poppit kit for your year and model motor, as they changed over the years.
  10. C

    Process for changing boat trailers?

    Gee, loosen the winch strap so you have 6" of slack. Tie the transom eyes to a tree and pull the trailer forward a bit pulling the transom back off the trailer until you can add blocks under the transom corners. Now drop the tongue and add the blocks under the transom corners, padded with...
  11. C

    Brass block drain plug leaking like a sieve

    Sorry, block drains and plugs are a bit different. Maybe replace both adaptors and plugs. From Flea-Bay: TWO PACK Mercruiser Exhaust Manifold & Engine Block Drain Plug KIT 22-16951Q1
  12. C

    Process for changing boat trailers?

    Take a ride to any marina and see how they block boats up. You may even see a boat similar to yours blocked up.
  13. C

    Brass block drain plug leaking like a sieve

    Std Garboard drain plugs are tapered. You would need a special NPT tap to clean the threads, vs a std bolt tap. The Garboard drain plugs do not normally leak, even when put on dry. If you have the correct plug for the garboard drain, and it leaks, you need to check the garboard drain fitting...
  14. C

    Buy a 5hp Mariner with a blown head gasket?

    You could try marineengine.com, ebasicpower.com or iBoats. Maybe they list another number.
  15. C

    2001 200hp Johnson Float Bowl 0439180

    I did not see any new ones for sale. What is wrong with yours?
  16. C

    VRO delete fuel mix ratio?

    Hesitation to accelerate could be due to a bad fuel pump diaphragm. If the diaphragm leaks, raw fuel can foul a spark plug. If/when the boat gets on plane, the leak can be too small to affect high speed operation.
  17. C

    Replacing my speedometer pickup what sealant to use

    Gee, any sealant that is suitable for below the waterline is fine. I used silicone for 50 years. Pure silicone is completely waterproof. Silicone is also fine for aluminum. Silicone is often used to caulk windows to siding trim made of aluminum. Life Seal is good for wet surfaces. If you...
  18. C

    Process for changing boat trailers?

    All or almost all power boats under 40 feet, may be blocked up in the corners of the transom and under the bow. Drop the tongue, put cement blocks and wood under the transom corners. Lift the tongue and put blocks and wood under the bow. Now you have leave to repair your trailer.
  19. C

    2007 Honda 225 loss of power

    You might check your compression. Did you do that when you first got the motor, as a comparison could be useful. What shape is the prop in?
  20. C

    Process for changing boat trailers?

    Gee, block up the boat and replace the bunks. Pressure treated lumber and a bit of indoor-outdoor carpet and some stainless steel staples.
Top