Search results

  1. R

    repair manual for 115 inline merc 1984

    know someone had one posted on here in pdf format downloaded it and it got erased out of my cpu somehow
  2. R

    update water on plugs 115 mariner inline 1984 motor trash

    well tore exhaust plate off and found oil and water mixture everywhere also found broken ring so i figure i have a cracked cylinder .....however i have another powerhead i can use so took exhaust plate off that motor to check condition and found some scoring on the top piston but it isnt bad...
  3. R

    THIS IS NUTS sticking needle valves in carbs

    hey guys have sticking needle valves in carbs on a 1984 115 hp mariner inline trash motor with side float bowl carbs ok this junk has had stickin needle valves for 3 years now have taken the boat to 4 different repair shops for them to tell me it was the stator,switchboxes,fuelpump, so i have...
  4. R

    sticking needle valves in carbs

    have a 1984 mariner 115 hp with the side bowl floats .had the needle and seats replaced and when i would blow air into the fuel inlet (by mouth only) could hardly pop the needle off the seat and the needle and seat are new is this normal being that i know the fuel pump only puts out around 3...
  5. R

    trigger magnet

    i have a 84 merc 115 hp inline 6 and took off flywheel the trigger magnet is split in one place are they supposed to be that way or should they be solid
  6. R

    sealing carb plugs

    what do you put on threaded brass plugs to seal the threads on merc carbs
  7. R

    mariner fuel pump question

    hey guys have a 1984 mariner 115 hp and the motor dies out at high speed changed switch boxes cuz a repair shop said they was bad but that didnt solve problem so was checkin the fuel pump and i have 3 lbs pressure at idle but checked the flow and idiling for 30 seconds it puts out 8 fl oz of...
  8. R

    1984 mariner 115 inline 6 boggs at wot

    motor runs fine except at wot when u throttle up to wot will run fine sometimes for about 30 seconds or so then boggs down to about 4000 rpm when u pump primer bulb motor motor picks right back up and runs fine for 30 seconds or so then bogs again ....if i continue to pump bulb motor continues...
  9. R

    mariner sticking in reverse

    hi guys i have a 84 mariner 115 hp that every time i put it in reverse gear the controls stick i have to raise the motor out of the water and rotate the propeller to get it to come out of reverse i know it is sticking in gear because you can return the controls to neutral and the starter will...
  10. R

    what year mariner

    lookin for year s/n # 6527845 mariner
  11. R

    mariner water leak

    hi guys i have a 84to86 mariner 115hp outboard and when its running i have water coming out around the number 3 spark plug does anyone know what could be causing this thanks in advance for the help
  12. R

    mariner outboard telltale

    hi guys i have a 84-86 not sure exact year mariner 115 outboard bought boat and started motor today and did not have constant stream of water from telltale i do have water coming out then it quits so i shut it off in fear that i would cook the motor is this normal ? also is there a way to give...
  13. R

    mariner controls

    does anyone know where to get controls for an 84-86 year 115 mariner outboard thanks
  14. R

    wire from gas fill to tank

    i have a wire running from my gas fill to my metal gas tank the gas tank just sits on the deck this is on an outboard i was wondering what this was for and if you need it as it doesn't look factory thanks guys
  15. R

    what do you guys think truck bed coating question

    i have replaced the deck of my boat and have fiberglassed over top of the plywood with 6 oz cloth using poly resin i have marideck vinyl for the floor i was thinking of spraying truck bed coating over the glass before laying down the vinyl as an extra waterproffing and to protect the glass as...
  16. R

    automotive undercoat

    i am in the process of replacing the plywood floor of a 1977 18' invader tri-hull once i finish pouring the foam. i have already replaced stringers, transom. my question is i noticed a black coating on the fiberglass that butts up to the plywood. could this be undercoating? have any of you...
  17. R

    stringer question

    hey guys got one question i replaced the wooden stringers on a boat i am currently restoring and i bedded the stringers with west system epoxy and glassed the sides is this an acceptable method of bedding the stringers as i have read on the forum to use construction glue. the old stringers sat...
View older results
Top