Search results

  1. fisheymikey

    head gasket?

    hi I have a 125 force 1988 I have 141 on all 4 cylinders I #4 cylinder spark plug is always much cleaner than all others. question #1: can there be a water leak even if I have good compression #2: can that cause a loss of power? #3: can it cause damage already...
  2. fisheymikey

    spark tester

    I am sure its easy to answer but im not sure... here is a spark tester from force but cant find any how to... I edited with paintshop to make easier for a description. I think I have a weak spark on all cylinders even if I reach 4400 rpms I assume I set the spark plug wire on #1 then set...
  3. fisheymikey

    stator force 125

    hi, I heard about Hi/Lo setup on the stator. what I was tokd that there is a specific way the stator should be installed on the motor. meaning the winding should be place facing a certain place and also even if the wires are the same color they cannot be inverted... I read my post and it seems...
  4. fisheymikey

    Need force prop

    hi! I have a force 125 1988 I want a 17 pitch I want a 15 stainless if possible... ebay EDIT mike
  5. fisheymikey

    sator output?

    force 125 1988 I have read numerous reads in regards of resistance my engine should have 500-800 I have 768 on both cold engine but after it runs and engine warm it spikes to 1000 then goes back to 768 is that normal? but more important when I take reading while engine is idling at 1500rpms...
  6. fisheymikey

    100hp 4 stroke yamaha 2001 inspection

    hi, I want to purchase a 100hp 4 stroke yamaha 2001. before I buy I want at least to do a compression check does anyone have the specs? also what else should I check for the guy seams a little sketchy or maybe is my paranoia therefore I would like to verify most common issues with this engine...
  7. fisheymikey

    burns a lot fuel

    I have 125 force 1988 trophy center console I came back from my trip but very happy how the boat ran but confused in regards of the over consumption of the boat. but im sure the question will come flying in regards how much when were and conditions so here it goes... the weather avrg choppy...
  8. fisheymikey

    milky white in entry of carb

    here is a pic of the carb I have a lot of milky substance before entry! I opened the carb bowl and its perfect clear glass fuel line filter before carbs look perfect. it is very humid with fog could that do it? please help I am supposed to leave in a few hours for my trip thanks mike
  9. fisheymikey

    transom mount

    im posting it here but maybe it will be moved... here are a pic that I noticed only this morning!! the other side is not cracked or the bottom what is the procedure do I need to redo all the transom? or cani drill a whole and insert epoxy sandwitch with 2 1/2 galvanised plates on either side...
  10. fisheymikey

    sarter issue

    I have a force 125... I did change the battery cables with 4 guage and sauder the ends. my battery is fully charged and does not go under 11 when starter is turning over I really belive its the starter I did see very little smoke came out of it. I cleaned the inside thoroully and there is...
  11. fisheymikey

    prop hub spline

    hi everyone! I have a prop but the splines do not match my shaft.. my friend has a commercial press and feels he could press the hub out... do u think its possible without damaging the prop thx
  12. fisheymikey

    battery cable

    I want to change the cable it seems a little old even melted a bit at the end... I have a force 125 1988 what gauge do u guys recommend or should I buy a booster cable 8 guage thanks mike
  13. fisheymikey

    install flywheel key

    guys I must be an idot or something but I cant seem to get this right... do I install it from on top or install the key then put the flywheel pls help I already sheared one mike
  14. fisheymikey

    rectifier test

    I just was checking my rectifier and I am puzzled.... when I have the engine not running it has a constant 12.3v that im assuming coming from my battery. when I have the engine running I see it drops from 12.4 to 5 to 6 to 12 to 6 etc... always dropping Is that normal? mike
  15. fisheymikey

    bleed tilt trim force 125

    I want to bleed the oil in the tilt trim I suspect some contamination.... creamy white I did use 30 non detergent oil so want to flush it out I remember some said remove one of the tubes then cycle up and down which one? mike
  16. fisheymikey

    stainless prop force 125

    if ever I get this engine running right... I was wondering if it easy to fing stainless props for a 125 force 1988? mike
  17. fisheymikey

    cylinder 1# and #3

    I am totally stumped all of a sudden cylinder 1&3 not firing I have force 125 1988 any idea maybe just a wiring diagram would help thx mike
  18. fisheymikey

    fuel vent making noise

    force 125 in 18.5 trophy UPDATE! when I put some gas a bunch of water leaked out of the vent what the heck?? I seem to hear a gagleling noise like drinking water there is not that much fuel in it but a weird noise any ideas? mike
  19. fisheymikey

    Splice ignition wire

    I think i found my stuttering /bogging down problem... As trying to figure out my symptoms i checked the spark plug boot and i saw its does not make a solid contact and my rps change when u twist the boot. Even when i applied dielectric grease. Thus my question can i splice the coil wire solder...
  20. fisheymikey

    in gear does not want to move

    force 125 1988 140 on all cylinders all 4 sparks... also if revove any spak plug boot immediate reaction. here is the problem in neutral I could go until 3000rpms in forward gear I go until 2000rpms and a full bogging down action. the only thing out of the ordinary was when I had to shift in...
Top