Search results

  1. fisheymikey

    cylinder #4 clean as a whistle

    I have a force 125 1988 on trophy 18.5 I have 140lbs on all cylinders here is the problem, all 3 cylinders above are relatively dirty and the bottom one is very clean. im assuming its due to the engine swap I made in the beginning they have used a silicone gasket. also when I remove spark...
  2. fisheymikey

    cam position force 125 1988

    here are some pics no matter what I do I cant seem to get it right... I listen to the link and sink but getting the screw in the middle of the scribe lines with the buttleflies open is impossible. these pics are the best I can do... what im I doing wrong mike
  3. fisheymikey

    sand in telltale

    I found sand in my telltale and was blocking the flow. I blew it out and now its free of sand and I have flow threw it but....... the flow is half the pressure. my question is do I need to do something to remove the sand somewhere else? do I change the impeller? can I flush out the system thx
  4. fisheymikey

    what the heck is this??

    after an amazing 5 days fishing I had some hesitations issues again. I think I found it but please confirm your theory please thanks
  5. fisheymikey

    force 125 1988 gargles

    well I here we go again... this is the symptom: it gargles at 3500 rpms then clears up and then sometimes runs rough at 4300 I have done the following: installed new see threw filter no bubbles clear installed fuel pump diaphragm changed all connection changed fuel lines primer bulb timing at...
  6. fisheymikey

    static timing

    I have a lot of different statements. can someone clarify please the following... i removed spark plugs and grounded them, removed the propeller, jumped the trigger safety. i want the know the following...there is 3 marks.. from left to right is it 32-30-28 that is what im assuming. if so i...
  7. fisheymikey

    Spark plug boot

    I have a force 125 1988 The boot on cylinder 1&3 have a slight rip at the elbow Even a little bit of grease comes out! Does that cause any issues to the boat... Meaning loss of power etc... Thanks for the help Mike
  8. fisheymikey

    engine stalling,starving,electrical....

    here is the link hope it works force 125 1988. I have a trophy 19 engine noise - YouTube I hope someone has any ideas... please any advice will help I have timed, new conectors compression on all 4 cylinder 141lbs mike
  9. fisheymikey

    i istalled the wrong installed the wrong spark plugs!!!!!

    I really hope I did not damage the engine.... I have a 125 force 1988 I installed BUHW instead of BUHX I also timed it accordingly I get around 4700 rpms. after inspection my bottom spark plus seams not to have combustion it looks very clean. am I hurting my engine. I don't have my timing...
  10. fisheymikey

    both carbs leaking

    hi everyone, as you look at the carbs from the boat to the back... top left there is one hole on each and was leaking fuel... what would that be I just rebuilt it and ran awesome. is maybe the floats stuck or needles are finished but they looked fine do I need to open the carbs again please...
  11. fisheymikey

    white discharge

    I have a 125 force after running it for a while in the big bin of water I get a white greasy residue in the bin should I be concerned?? mike
  12. fisheymikey

    idle spiraticaly... force 125 88

    hi to everyone! at full throttle I have no issues revs all the way to 4900 at sounds great at 1500rpms forward gear im getting like a surge of a 200rpms up down I have cleaned the cabs very well and adjusted the floats to spec. needle are clean please help I have 2 days left to get her...
  13. fisheymikey

    fuel issue

    hi everyone, I have a fuel issue and I feel like an idiot but cant seam to figure out it seams when I don't connect the fuel line to the fuel filter the bulb primer get the gas there quickly but when it connect its like it has trapped air and no matter how much I sqeese the bulb it does not...
  14. fisheymikey

    force 125 heat buzzard

    hi! I am not sure if my buzzard is working. its a black with 3 screw in the back tried adding direct current without any sounds. or maybe im not doing it right. how do you check if it working also after doing the trouble shooting I saw it cost 45$ for a buzzards that crazy part...
  15. fisheymikey

    force 125 1988 carburetor

    hi everyone, I have done numerous repairs on this engine and thanks to everyone I have made this boat go pretty well. but last thing is a must I find the motor a little rough on 2200-2800rpms and also on idle it shuts off. I want to do it right so im going to buy a timing light ant etc...
View older results
Top