Search results

  1. fisheymikey

    force 125 hesitation

    here my motor ready to go in the water... what do you think the hesitation is? I put timing light on each plug no misfire, float are adjusted with carbs immaculate... transparent fuel filter before carbs full and primer bulb rock hard any ideas?? force 125 hesitation - YouTube thanks
  2. fisheymikey

    compression changed after new headgasket

    I have a 125 1987. I recently changed the head gasket during the winter months. I followed the process of torque, last year I had 141 on all 4 cylinders now im getting 125 on all 4. can my compression gauge be the reason or a weak battery could do that? thanks mike
  3. fisheymikey

    throttle 125 force

    here is throttle end connectors. I did not take a picture before removal. which end goes were? the long one goes to throttle and the short to the gear case? or vise versa thanks mike
  4. fisheymikey

    are all carbs the same

    hi everyone I have 125 1988 I have 2 carbs one has tc-xxxx and the otherone has only numbers. question is are all force 125 from 1983 and up are the same? if not please tell me what to look for thanks mike
  5. fisheymikey

    hds strucute scan

    hi everyone here is a pic of my current setup I need to add my new lss2 ducer... I want to install it were the arrow ends don't know what that gadget is! please let me know your advise were I should put all my ducers thanks mike
  6. fisheymikey

    Vortex prop

    hi I ordered the Vortex prop 15 pitch for my 1988 125 has anyone tried them? are they the same company with Michigan? thanks
  7. fisheymikey

    fuel pump check valve

    hi everyone! just received my check valves... im aware that there is a certain way to install them. I looked at the diagram but does not indicated how. I am also aware one of them is very difficult to get to... any details how to remove would be great thanks mike
  8. fisheymikey

    hds7 gen2 with hds7 touch

    hi everyone! I have done a lot of research with my hds devices. my hdstouch is on its way and I have a question in regards of syncing both unit. what I understand from a prostaffer lowrance. when I connect both devices via Ethernet cable they will both automatically populate all info i.e...
  9. fisheymikey

    flush engine

    force125 1988 I was wondering if there is a way to flush the engine. I have seen calcium build up on other ppl engines and want to do some preventing measures before I have a actual problem. my engine does not over heat so I think its flowing correctly. is there a addictive I could add to the...
  10. fisheymikey

    puddle drain WOW!

    here is the puddle drain on my 1988 125 imassuming the black stuff is not part of the gasket. when I rubbed it the black stuff coming apart like fiber material is that normal? can I go ahead and remove all the gasket its pretty stuck on it thanks
  11. fisheymikey

    exhaust gasket torque

    hi I have 125 1988 well Im pretty sure I did not do the right procedure for installing the exhaust gasket. I did the gasket with black gasket maker and never retorque it after initial installation 1st question should I just retorque if so at what poundage? or should I remove the head again and...
  12. fisheymikey

    fuel pump valve

    hi everyone! I have fore 125 1988 I was told on a other thread thad my valve could be bad due to the bottom cylinder #4 is washing clean i.e seam to be leaner than other cylinders. I checked on iboat and to ship to Canada is a whopping 30$ the parts itself is only 11.52. is there a way to...
  13. fisheymikey

    hds 7 gen 2 transducer

    hi everyone! I just was going threw some tutorials in regards my unit and I never set the transducer type I looked all over the place on the transducer and there is no indedification on the cable or the transducer itself.. is there way to figure this out? thanks mike
  14. fisheymikey

    testing my dva meter

    hi everyone! I just finished builing my dva adapter and works great... tested on a few batteries and works!! now I have a few question I did look at the outboard ignition web site and they clearly indicated witch wire to test from.. but the only question is do I do the testing during running? at...
  15. fisheymikey

    powerhead bolts

    hi here are 2 bolts from the bottom severely corroded does that mean my gasket was faulty? thanks mike
  16. fisheymikey

    force 125 carb question

    hi all! I have a force 125 1988 I want to service my carbs to make sure they will be running great this spring. I checked the float and one of them cracked!! it have a separation in it and probably did cause some running problems. but my question is what would you you do as a procedure to...
  17. fisheymikey

    powerhead torque

    hi everyone! I have a force 125 1988 cleaned the head getting the head gasket can some share the tourque sequence for reinstalling the head im aware it takes 2 stage torque step but I don't understand the spiral motion in regards of the bolts im a visual person thus a pic would be greatly...
  18. fisheymikey

    powerhead force 125

    Hi I have a force 125 1988 I remove the head and gasket How do I prep the head and block? Do I use sandpaper to remove small leftovers bits from the gasket? Acetone? Any guide line would be great Thx
  19. fisheymikey

    fuel recirculation

    I have read a few post with fuel recirculation issues... were do find the area to inspect? I have read force 125 1989 are notorious for that being clogged! I have the engine apart just curious to know ere it is? thx
  20. fisheymikey

    check reed

    i have removed the carburetors from the block and I read there is a way to check if the reeds are functional... what am I looking for.... rust warp for me I looked but cant even recognize were they are hoping someone has some input thanks
Top