Search results

  1. L

    97 350 vortec knocks only under a load

    I have a 1986 286 searay 350 mercruiser with alpha outdrive. Engine was replaced a few years ago with a 1997 350 vortec engine. 2 weeks ago i had a pretty bad overheat. Melted the exhaust couplers. Replaced the water pump, exhaust couplers, shift cable. Risers and manifolds looked ok. Started...
  2. L

    Mercruiser 350 center riser gaskets

    Need to replace my riser gaskets. It's on a 1986 mercruiser 350 with center mounted risers. Mine used a gasket then a steele shim then another gasket. The problem i'm running into is finding the correct gaskets. They list 2 types full flow or a gasket that has 2 small vent holes. The one gasket...
  3. L

    mercruiser shift cable nut installation

    Working on a 1986 mercruiser alpha 1 with a 5.7 engine. Last year after installing a new shift cable i could never get the boat to shift in and out of gear properly. Always had to go slightly past neutral for it to actually go into neutral. Sometimes when going into forward it doesn't engage...
  4. L

    removing 150 yamaha's from engine bracket

    Will this hook support the weight of a 2 stroke yamaha 150? I have to pull both motors to replace my engine bracket.
  5. L

    2-stroke oil hoses what to use?

    On my 87 yamaha's 150 2-stroke i need to replace the oil feed hoses from the remote tank to the tank on the engine. I also would like to replace all the hoses that go from the oil injection pump to the cylinders as well. And i guess while im at it i want to replace the oil fill hose from the gun...
  6. L

    alumn grady drive pitted

    I recently a 1986 24 offshore with twin 150 yamahas. I took notice the grady drive engine bracket is started to show signs of corrosion and pitting. The bracket still seems solid yet. I would like to clean all the bottom paint off then wire wheel it. I know the bottom paint has to be copper...
  7. L

    yamaha remote oil tank repair kits?

    I have a 1986 grady white 24 offshore with twin 150 yamaha 2-strokes. When i fill the remote oil tanks up i have some oil leaking out of the sensors. Do they make a repair kit for this if so where to get them.
  8. L

    trim filling and filling 1987 150 yamaha

    I have 1987 twin 150 yamaha's. The port engine when operating the trim/tilt is a little sluggish to respond. Sounds like it's low on fluid. According the manual i have. They have u putting the engine on the tilt like using the manual release screw. Then pulling the motor cover and filling till...
  9. L

    best to trailer with outboards?

    I'm new to the outboard world. Recently bought a grady white with twin yamaha 150 outboards. When i towed it home i put the outboards all the way up then used the tilt lock lever to hold them in place. having them down isn't really an option. Will having them on the tilt lock hurt anything?
  10. L

    replacing implellors 1986 yamaha's 150 2 stroke

    Is there anything special to replacing the water pump/impellor in the lower unit? I've always own i/o's this is my first outboard boat. Do u just unbolt the lower unit and pull it down? Do the lowers have to be in gear or doesn't matter with an outboard?
  11. L

    odd tire wear on a venture tandem trailer

    While starting to prep the boat and trailer for spring i took notice that the right front tire on the front axle and the left rear tire on the rear axle are badly feathered. The trailer is a venture VATB-8025 alum I-beam. I bought this trailer new last march. I have put less then 1000 miles on...
  12. L

    1986 mercruiser not shifting right from forward to neutral

    I replaced the lower shift cable on a 86 mercruiser outdrive. Reverse works perfect. But when i go from forwrd to neutral i actually have to go slightly past the neutral detent to actually go in neutral. I checked the cable from the throttle lever to the shift bracket assembly and it moves with...
  13. L

    correct of installing lower shift cable 86 mercruiser alpha outdrive

    Got a shift cable from the local boat place. The kit now comes with the cable, new thottle end and new shifter lever at the drive. What is the procedure for installing the outer casing along with the shift lever? I found instructions on how to adjust the cable once installed..
  14. L

    lights for bunks?

    i just bought a new bunk trailer for my boat. I'm looking for led lights to attach to the bunks so at night time the wife can see where the bunks are when she's loading the boat onto the trailer. The lights would have to be able to handle the occ brackish waters but mainly fresh water
  15. L

    site for finding used trucks

    I'm using autotrader.com to help locate a used tow vechile. Are there any other decent sites for finding used vechiles?
  16. L

    mercarb leaking fuel out of venturies

    Working on a 1987 mercruiser 470 engine. Engine idles rough. when giving gas it stalls or bogs down. Engine 90% of the time just stalls when idling. Traced the problem to fuel leaking out of the venturies. Even with engine shut off fuel leaks out of the venturies. Rebuilt the carb. Doubled...
  17. L

    Mat to cushion feet?

    I like driving the boat standing up. Most times i'm bare footed. Is there some type of mat/cushion for the deck?
  18. L

    how far should the outdrive splines go into the coupler?

    Working on a 1979 grady white i/o with a 1987 470 (3.7) engine with a new sei 106 drive. Tonight at the local lake when taking the boat off the trailer i lost propulsation and then heard a grinding noise. Got the boat back on the trailer. removed the out drive. Found the spline shaft was only...
  19. L

    how do u wire a 7 terminal nav/anchor switch with no common terminal?

    1 2 3 4 5 6 7 terminal 1 is ground. terminals 4&5 are both power feeds. terminals 2&3 are for nav lights. terminals 6&7 are for anchor. bow lights and stern light are on one circuit. front portion of all around lite is on another circuit. The rear portion of the all around lite is on another...
  20. L

    maxium length for bunk supports?

    Looking at converting my trailer over to bunks which is currently a roller trailer. I'm looking at around 1300 bucks just for 32 rollers and 8 pairs of quad rollers. for a easy loader trailer. The boat fully loaded weighs around 8000lbs. Currently my support cross members are mounted about 10...
Top