Search results

  1. lilmandavis

    280 flywheel coupler question

    will the coupler bolt up to either size chevy flywheel. old style 280 volvo chevy 5.7 l late 80's i have the smaller size flywheel in there now getting ready for the bigger flywheel.
  2. lilmandavis

    volvo 350 flywheel question

    OK i have found a flywheel housing for my old 280 drive volvo to fit a 14 inch flywheel. the question is on this 350 87ish 5.7l block the stater holes only accomodate the offset bolt pattern. does this flywheel need to be internally or externally balanced? if need be I can go get the block...
  3. lilmandavis

    volvo bellhousing questions

    I have aquired a sbc 350 gen 2. I have a boat with an old style 280. A 12 3/4 flywheel is what is in it. as far as i can tell there isnt goin to be enough room for a 14'' flywheel in that housing. I remember the dimensions from a ways back when i put in bell housing bearings and seals. Question...
  4. lilmandavis

    old volvo 280 drive and new style 350 engine

    I am having a problem getting the starter drive gear to line up with the flywheel. It is a volvo 280 drive and a rebuilt 0010 casting # 350 block. My guess is the old style flywheel is to small for the new style bolt pattern on the starter. What are my options as to get the extra 1/2inch i need...
  5. lilmandavis

    alpha one question

    was wondering what the small hole on the front of the lower unit does. looks to be about an 1/8 inch hole. and where does the rubber hose go to after it leaves the port in front of the shift shaft? the one im looking at has been J B welded closed?
  6. lilmandavis

    460

    What do you experts recomend on a stock cam for a 87 ford 460? I was trying to figure out what a good grind would be. There is a roller set up in it now. Goin to keep that, just want to tune the cam down a bit. Its a little to lopey. thanks.
  7. lilmandavis

    78 inline 6 1400

    I was looking for the diagrams for the fuel line routing. I cannot find the pictures on where to put the lines at. Im talking about the barb fittings where the bearings are. My pic of them i took before rebuild are gone.
  8. lilmandavis

    Volvo 280 / 270

    What exactly is the difference between the two? will the lower and upper off a 270 bolt up to the 280. Will the gears be interchangable? Are the drive shaft bearings the same? THe reason is i have lots of parts for a 270 but have a 280 on my ciera sunbridge 2450 with 305 in it. the gear oil is...
  9. lilmandavis

    my new freebie!

    it is complete and running. the engine looks like brand new although i have an extra 1400 power tower. it came with trailer, boat, custom cover, two gel cell bats, and the 115 chrysler. its being sanded down as we speak and goin to be pretty white and blue. the interior is great as well. its a...
  10. lilmandavis

    115 chrysler bracket

    do any of you guys know where to find a transome bracket to bolt on the back of a 20' cuddy? im looking for something like a swim platform that also will hold up a 115 hp outboard. and room for a kicker bracket?
  11. lilmandavis

    115 chrysler bracket?

    do any of you guys know where to find a transome bracket to bolt on the back of a 20' cuddy? im looking for something like a swim platform that also will hold up a 115 hp outboard. and room for a kicker bracket?
  12. lilmandavis

    anodes

    what kind of anodes would one use on his composite volvo outdrive?
  13. lilmandavis

    marine diesel books

    i figured don or rodbolt could help me out on this one. i am currently thinkin on switching shops. right now all i work on is gas inboards. i have alot of nonmarine diesel expierence. is there any books publised by volvo and the other manufacturers on extensive engine theory on new style...
  14. lilmandavis

    bilge water in cabin cruiser

    in my cabin cruiser. the bottom of the bilge always has some water in it. what is the best way to keep the mosquito larve out of it?
  15. lilmandavis

    il6 merc ignition swap

    could a ignition off an 80's style il6 115 work on a 78 il6 140? the 140 has a distrubutor and the 115 has the six coils. they have the same diameter flywheel. could i take the whole setup, wires and all and install that on the 140?
  16. lilmandavis

    11hp kubota.

    i have this old guy who is parting out his sail boat and he wants me to take the kubota engine and drive.im not to much on sail boats but exactly what is this setup? is it a screw drive out like an outdrive? is it some sort of an outboard with remote steering? i havent seen it yet and its 25...
  17. lilmandavis

    chrysler 60

    on these old things, does the temp switch have any effect on the performance of these things or is it just for a gauge or buzzer? the thing is, it sounds like it wants to run great but, chokes out the same time everytime. it goes, pop! goes, pop! goes, pop!. and it wont rev out. its got great...
  18. lilmandavis

    volvo outdrive 270

    how does the hydraulic pump come off the volvos on the early 70's model. its a 270. looks as if its a direct drive off the output shaft. ive got it to turn abut dont want to pry on it it as its still good. removing the drive and engine from a junk boat.
  19. lilmandavis

    timing on a 79 il1400 6cyl.

    where do the timing marks line up as im bolting on the new timing belt after the rebuild? im not quite understanding it wanted some more info on it!
  20. lilmandavis

    old glastron i got for free.

    theres a rebuilt volvo 270 in this glastron i just got for free. these outdrives, how are they as far as being durable. the boat has been garage stored. theres also an engine in this thing but im not sure what it is. and no i dont have the serial numbers on it yet. but its a volvo b-30 inline 6...
Top