Search results

  1. D

    Best fuel stabilizer for older 2 strokes

    With the new standard petrol being e10 here in the UK and Ireland, does anyone know what the best fuel stabilizer would be for an older 1977 evinrude 15hp. Are the stabilizers that are engineered for newer cars, too harsh for an older worn 2 stroke. Thanks in advance
  2. D

    1977 evinrude 15hp water flow

    thank you very much, was not sure if it was the prop or the exhaust holes were the main opening for the warm water
  3. D

    1977 evinrude 15hp water flow

    ive replaced the thermostat, it pumps water perfectly but just not warm water through the exhaust ports
  4. D

    1977 evinrude 15hp water flow

    I've recently got my hands on an evinrude 15hp. I've done my normal checks and service, gears case lube, seals, impellar kit, carb kit, thermostat etc. And it runs perfectly. Starts first pull and idles perfectly. This is more of a precaution question. The tell tale pumps water very strong even...
  5. D

    Best way to waterproof plywood transom

    I thought that the whole point of spar varnish was to be water resistant and not fully waterproof as to allow the wood to breathe? That's my understanding as to why people use spar varnish over an epoxy coating
  6. D

    Best way to waterproof plywood transom

    so my plan is to use the old timers formula with epifans clear spar varnish on marine grade plywood. is there anything that I should change or add to this plan, thanks appreciate the replies
  7. D

    Best way to waterproof plywood transom

    What did you do to the treated wood in order for it to be kept for so long without any rot?
  8. D

    Best way to waterproof plywood transom

    Thank you very much for the invaluable information. Just wondering what males that formula better than if I was to just use multiple coats of spar varnish on its own? Appreciate it
  9. D

    Best way to waterproof plywood transom

    I'm remaking the transom of my 13ft alluminium boat and have 18mm marine grade plywood that I'm going to use, I'm just wondering what is the best sealer to coat the plywood in, in order to make it as waterproof as possible, thanks
  10. D

    Removal of alluminum boat fiberglass top cap

    Well, I've went and taken the cap off. The hull and gunwhale seem to be strong enough without the cap attached ...
  11. D

    Removal of alluminum boat fiberglass top cap

    After you separated them was the hull considerably less sturdy even though its alluminium?
  12. D

    Removal of alluminum boat fiberglass top cap

    And what would be the best way to add structure with the top cap gone?
  13. D

    Removal of alluminum boat fiberglass top cap

    Do you recommend removing it for this boat or would it be better to keep it on, thanks for the reply appreciate it
  14. D

    Removal of alluminum boat fiberglass top cap

    I have an old 12ft alluminium boat with a fiberglass top cap (I think it's called a top cap) I was just wondering if anyone knows how to remove it and if I would be able to remove it without destroying it as such so that if I wanted I could put it back on. Pictures below
  15. D

    Upgrades to old alluminum boat

    I have an old alluminum boat paired with a 1977 johnson 6hp, and was just wondering if anyone has any ideas on some fishing type upgrades or upgrades in general that they think would work well. I have pictures attached below
  16. D

    1966 johnson 6hp oil return hose nipple

    Appreciate the detailed information, I have two 6hp 1977 and 1965, I've take the powerhead of the 1966 to paint and replace head gasket and other gaskets, I was just curious as the oil tube is the only part of the engine that I havent replaced or fixed but from what you've said I think it should...
  17. D

    1966 johnson 6hp oil return hose nipple

    Ok thanks so much for the information, it's more the fact that I have the powerhead completed apart to replace old gaskets as I've done everything else on the motor and was just curious about the oiling system, thanks for the information
  18. D

    1966 johnson 6hp oil return hose nipple

    Say its not allowing oil to pass, do you know what would happen then? Would the main bearing that its oiling fail or?
  19. D

    1966 johnson 6hp oil return hose nipple

    I've put copper wire in with carb cleaner and it goes in about an inch and then just completely hits a wall. Like wont go any futher
  20. D

    1966 johnson 6hp oil return hose nipple

    I've taken off the oil return hose on my 1966 johnson 6hp to see if any blockages are present. I can blow air through the top nipple with no resistance but the lower nipple is a different story. I cant get air to go through. Its getting fully blocked. Wondering if this is normal or how to fix Thanks
Top