Search results

  1. cwrhyne

    Volvo Penta DP-SM Steering actuator leak. 21910902

    I have a leaking steering actuator. The boat is a 99 Crownline 202 Volvo Penta DP-SM Do I buy a rebuild kit for 24 year old steering actuator and attempt to do it myself. I am pretty handy. 50.00 Do I send it to 5 star marine and have them rebuild a 24 year old steering actuator? I heard...
  2. cwrhyne

    Adding speakers to the stern.

    I would like to add 2 5.25 speakers to the stern of my 1999 crownline 202. The cutout for these speakers is 4.75. I have enough room to add them under the vents. My question is Would that structurally hurt the boat? Like dragging towables? I'm attaching a picture of a 202. Not my boat but...
  3. cwrhyne

    In need of Aftermarket Armrest

    I have a 1999 crownline 202. Has anyone added an armrest behind the engine controls? Like this?
  4. cwrhyne

    1999 5.7 dp-sm

    I was winterizing my boat yesterday and I found something that concerned me. While taking off the bottom hose off the raw water pump I noticed that where it connects it is a 2 piece deal and it swivels inside the upper piece. like its supposed to be glued in or something and it is not. like if...
  5. cwrhyne

    Filling block with antifreeze

    1999 Volvo Penta 5.7 GS DP-SM I am winterizing this weekend and after reading all the stickies I am going to drain all the water from all the plugs and hoses per the owners manual. I am choosing to fill the block with antifreeze even though I know I don't have to but because I believe in being...
  6. cwrhyne

    99 dp-sm 1engine alignment

    I must have read that sticky on engine alignment 30 times before I aligned my engine. I'm not real sure I hit the alignment bar hard enough when I set the gimbal bearing. So my question is..if I had to raise the mounts up two full turns on a 99 model does that seem excessive? Like I didn't have...
  7. cwrhyne

    Dp-sm nyloc outdrive nuts

    The part number is 3853329 for the 6 nyloc nuts for the outdrive. The original have a flange. Sierras part number is 18-3730 and do not have a flange. Are these OK to use? I can find these at Menards. Also zinc or stainless?
  8. cwrhyne

    U joint splines dp-sm

    What is the best brand of molybdenum trioxide grease to use for u joint spline? I can't seem to find anything except Walmart brand super tech Moly grease or Valvoline moly. Should I use this or something else. I'll buy whatever is best. ​​​
  9. cwrhyne

    99 dp-sm oil in bellows

    After removing my outdrive for the first time I noticed some oil in the bellows. I would say maybe a few teaspoons down in the creases. Would that be engine oil or drive oil? I also aligned my engine. I had to turn the nuts 2 full turns to make it right.. But I'm almost out of threads. What do I...
  10. cwrhyne

    Drive removal 99 dp-sm 1.95

    I have read all the stickies and have the shop manual and I either missed it or it doesn't say. I'm getting ready to remove drive to grease u-joints. Does drive have to be in gear?
  11. cwrhyne

    Shift cover broken

    I just took my boat out of my garage and there is a big hole in the shift cover. I must have hit something lady time out. Will it keep me from going to the lake this weekend? Be OK until I get a replacement? It's on the top right corner.
  12. cwrhyne

    Gimbal Bearing 1999 DP-SM 1.95

    I'll have the out drive off of my 99 Crownline this weekend. I have owned the boat for 3 years. Would it be a good idea to go ahead and change the gimbal bearing while I'm in there? As far as I know it's not given me any problems. Should it be changed regularly? Like every so many hours or...
  13. cwrhyne

    Gear oil change

    In September of 2016 right after I bought my Crownline I took it to an authorized Volvo service shop in Marion IL. I asked them to winterize it and change engine oil and drive oil. Last week I decided to change both oils before I took the family out for the first time this year. The gear oil...
  14. cwrhyne

    1999 Volvo Penta DP-Sm

    My local mechanic refuses to work on Volvos so I'm forced to do things myself. I need to remove my outdrive to grease my u-joints and gimbal bearing. I have bought a jack from stumpys to remove it. My question is what should I replace while Im in there? Bellows? What should I look for? I read...
Top