Search results

  1. N

    Installing new stereo head (Kenwood KMR-M308BT) with amps

    Audio noob here. Old stereo head unit gave out. Purchased a new Kenwood KMR-M308BT Marine head unit. Below is a pic of the back of the unit. Has normal wiring harness with wires for speakers and one set up output jacks for rear/subwoofer connection. The port to the left of the output red jack is...
  2. N

    Advice on adding a Trolling Motor to a 25' Suntracker

    Have a 25' Suntracker signature with 60HP 2stroke bigfoot. Used exclusively on a small private lake which has a no wake zone all around the perimeter and in no wake coves. We spend most of our time puttering around the lake in the no wake zone. Running the outboard to putter seems to be overkill...
  3. N

    Harness or Tow bar?

    Have a 1997 Sun Tracker Signature 25' Party Barge. 60HP Merc Big Foot Two Stroke. Would like to pull a tube. No high speeds and on our private lake, we're limited to one rider at a time. My preference would be for a Stainless Tower but I haven't been able to find one to fit my toon online...
  4. N

    Ideas for speakers covered when pontoon doors are in open position

    Re: Ideas for speakers covered when pontoon doors are in open position Close the doors? Weeelllll golllly, I'd nubber thot o that there idear. Seriously. We open the doors sometimes so the dog can look out easily and when other boats tie up. Below is a pic. I was thinking about finding a few...
  5. N

    Pontoon boat decals

    Re: Pontoon boat decals here is a pic. This is where the big suntracker logo was previously.
  6. N

    Ideas for speakers covered when pontoon doors are in open position

    When my 1997 Party Barge has the doors in the full open position, the speakers in the arm rest bases (stock OEM position) are covered by the door panel which mutes the sound and causes rattles. Looking for ideas or products that would allow speaker sound to come through door panels with out...
  7. N

    Before I order Bearing Buddies...

    Re: Before I order Bearing Buddies... Ok all the above helps. I'm not used to the words "cadillac of" being used in reference to Sun Tracker :D I should have clarified...of my four hubs, only two still have the rubber plug intact. Plus I think the previous owner was either just messy or way...
  8. N

    Before I order Bearing Buddies...

    Hubs have what I'll call "poor mans" (Sun Tracker Trailstar) protector caps now (see photo). Have the rubber plug in middle over grease fittings. I assume you just pry off with a screw driver? I tried a bit with old screwdriver and a hammer, but they didn't seem to budge. Before I really...
  9. N

    Fuel/Water separator with a 60HP two stroke

    More details in a thread in the Mercury forum at http://forums.iboats.com/mercury-mariner-outboards/fuel-delivery-advice-needed-605311.html. That forum gets so many questions.... Any fellow tooners using a fuel/water separator with a two stroke outboard? Is it normal to affect the firmness of...
  10. N

    Have you checked your fire extinguisher?

    Not really Pontoon specific, but the Safety forum isn't very active. When I bought my new to me Barge last year, I had a lot of things to address. Totally ignored the fire extinguisher. It was one of those cheap types with no gauge on it. It was there, so I was good. Getting ready to put the...
  11. N

    Pontoon trailer guide options

    Have a bunk style trailer for 25' Party Barge. It has two pairs of the roller style guides (see pic), both pairs mounted on the front half of the trailer. I would like to make loading as easy as possible, so am weighing several optional approaches: Add another pair or two of the roller...
  12. N

    Fuel Delivery advice needed

    Posted in Pontoons earlier...should have posted here. I have a Potoon with a 22' gallon tank and a 60HP two stroke 2003 Mercury Big Foot. After some issues with bad fuel and/or water in fuel last year, I added a water/fuel separator in the off season. I had one of those see thru in-line fuel...
  13. N

    Fuel Delivery advice needed

    I have a toon with a 22' gallon tank and a 60HP two stroke 2003 Mercury Big Foot. After some issues with bad fuel and/or water in fuel last year, I added a water/fuel separator in the off season. I had one of those see thru in-line fuel filters already, and I just left it on after adding the...
  14. N

    Subwoofer Scuba tank

    Re: Subwoofer Scuba tank Another amusing option... hmmmm
  15. N

    Hummingbird 400tx transducer and sender question

    Never owned a fish/depth finder before... Pontoon I bought last year has a Hummingbird 400tx but the previous owner hit something and knocked off the transducer/sender(s). See pic to see what's left below the water line. Not sure how clear the pics show it but one cable is going to the bracket...
  16. N

    Subwoofer Scuba tank

    Audio purists....don't laugh. Subwoofer disguised as a scuba tank?!? I'm wanting to add a subwoofer to my pontoon. Not looking to create waves in the water since we are on a smallish private lake with noise rules due to waterfront houses. Bought my pontoon last year and it has two amps (one...
  17. N

    Removing water from toons and broken vent plugs

    I heard some water in the back section of one of my toons on 97 Sun Tracker Signature 25. Still haven't figured out how/where it's getting in, but I'm pretty sure it's a factory weld issue well above the water line. I've tried soapy water spray and forced some air in the vent but can't find any...
  18. N

    its getting borning some one needs to break something

    Re: its getting borning some one needs to break something Here's the cover support structure I built using hi pressure PVC pipe. The top fittings I got from a canopy supply company. I wish I would have ordered steeper angle fittings to help prevent snow load. On top I strapped down a standard...
  19. N

    SunTracker Party Barge - Removing rear cushion from carpeted platform

    Re: SunTracker Party Barge - Removing rear cushion from carpeted platform Here are a few other pics, but not sure how helpful they will be. I took the whole rear bench/seat assembly off the boat and removed the mounting brackets. There are no other visible fasteners to remove to detach the...
  20. N

    SunTracker Party Barge - Removing rear cushion from carpeted platform

    Re: SunTracker Party Barge - Removing rear cushion from carpeted platform I'll add pictures tomorrow. Attached is a picture of the seat. There can't be any screws under the carpet since the carpet is wrapped up around the sides, so the screw heads would be under the carpet...no way to tighten...
Top