Search results

  1. danoutbard

    Model/Year ?

    My friend here in Canada has this model # E20CRCIM (see picture). This says that this is a Rude / 20 HP / Rope Start / 1981, It seems that OMC did not made any 20hp in 1981. Im looking for parts,BRP, Ishopmarine and others do not list any 20hp in 1981. Any ideas on that? Thanks
  2. danoutbard

    Starcraft restoration question

    Re: Starcraft restoration question Hi folks, Here's some pictures of my Starcraft inner-sides so you can help me install some braces. I'm taking very seriously the fact that i did remove the old panels and that there is no support for the outer-chine Thanks a lot :)
  3. danoutbard

    Starcraft restoration question

    Re: Starcraft restoration question Here is some more pix prior to restore to help indentify model and year. Thanks for all replies N.B Stay tune more pix to come :joyous:
  4. danoutbard

    Starcraft restoration question

    Hi folks, I did restore this Starcraft (pix attach) a couple of years ago. While doing this, i did remove the side panels covering the inside and also i removed the old seats. By doing this, i ended up with the boat a lot lighter than it was. I also put a 90hp (maximum alowed) to replace the...
  5. danoutbard

    Johnson 150hp dies at speed

    Re: Johnson 150hp dies at speed Yeap time to check spark,do you have an air gap tester?
  6. danoutbard

    Is there a way to test a rectifier?

    Re: Is there a way to test a rectifier? Actually 4 diodes in bridge...
  7. danoutbard

    water in oil

    Re: water in oil Here is something to help?. http://shop2.evinrude.com/Index.aspx?s1=bad13891i6l6lhfmsitmb1e314&catalog_id=5&siteid=1
  8. danoutbard

    Sealing crank case halves.

    Re: Sealing crank case halves. Poeple at Marine Medic Lakefield Ontario use ThreeBond 1194 Did use it on four motors, works perfectly
  9. danoutbard

    Yamaha P250

    Does anyone know something about this motor ? Year, HP ? I am about to buy it, but there is not much about it on the web. Yamaha P250 GS22719
  10. danoutbard

    J79TLCRD and OMC remote

    Hi, I have a just finish rebuild this 1984 John 70hp & i have and issue with the remote. With no remote motor start and run perfect. With the remote the kill switch work in reverse. I have to push and hold it to start and run, when i release it stop. Push to prime work ok. This remote was not...
  11. danoutbard

    J70TLCRD wiring diagram

    I need to see a wiring diagram for my Johnson 70 hp 1983. I do have the Seloc book wiring, but it does not say where to put the jumpers on the terminal block. Its a 5 points terminal block with one or two jumpers.
  12. danoutbard

    Mariner 115 hp 1997 Serial ?

    Where can i find the serial number on this 115 Mariner 1997. I need to know the length of the transom mid section. Thanks
  13. danoutbard

    Water in gearcase J90TLCOS

    My 90hp Johnny is getting water in the gearcase. I did change the prop shaft seals and O rings but still. I think i m gonna have to do the driveshaft seals also. The shifter also has seal and gasket. Anyone experienced this?
  14. danoutbard

    97 Johnson 90HP Won't Start

    Re: 97 Johnson 90HP Won't Start A good spark should jump a half inch gap...find a way to test create that gap or buy a spark gap tester
  15. danoutbard

    Shift lever has moved

    I have just starded a new project|: Johnny 1984 70 hp. I bought the motor all in pieces and im pretty shure the shift lever has moved from its calibrated position. Appart from trials and errors is there an easy way to mesure it to be shure i have it right the first time i insert the LU ?
  16. danoutbard

    Johnson control won't shift to reverse

    Re: Johnson control won't shift to reverse Had the same problem and replace this piece
  17. danoutbard

    Johnson 90 will not go over 2200 rpm at wot in the water after complete overhaul

    Re: Johnson 90 will not go over 2200 rpm at wot in the water after complete overhaul Finally nailed it !!!!!!!!!!!! Coil 2 & 4 were reversed thanks to a bloody wrong shematics:mad::facepalm: Can somebody confirm this shematic's wrong, blue orange plug 1 & 2 not 1 & 4 Thanks to all who...
  18. danoutbard

    Johnson 90 will not go over 2200 rpm at wot in the water after complete overhaul

    Re: Johnson 90 will not go over 2200 rpm at wot in the water after complete overhaul I have two Johnson Type II carbs there were no needles ??? Thanks
  19. danoutbard

    Johnson 90 will not go over 2200 rpm at wot in the water after complete overhaul

    Re: Johnson 90 will not go over 2200 rpm at wot in the water after complete overhaul Ok, had time to work on the motor (J90tlcos) this week-end, here's what i did. Did a spark test: spark does jump 7/16" on all cylinder Remove and disassemble the carbs : carbs were clean with no gum no...
  20. danoutbard

    Johnson 90 will not go over 2200 rpm at wot in the water after complete overhaul

    Re: Johnson 90 will not go over 2200 rpm at wot in the water after complete overhaul Hi again, I have this pump in the garage to replace the vro, but it has only 2 nipples. I red here that i can cancel the vacuum pulse line and we're ok. Can somebody give me confirmation on that please ...
Top