Search results

  1. P

    Power head replacment

    Trying to get a replacement for a Johnson motor Mod. 5JRCSS. The cover says 4.5 But do I look for a motor for a 4.5 or 5 HP? Or will something in the same range work. I am really looking for remanufactured and not used, any help where to look would be great.
  2. P

    Electric brake help

    2005 Silverado using Teconsa brake controller I have power to unit, black wire hot, when Irun ground to blue wire I get green light on controller, when I ground red no light on controller or test , when I ground white wire no power to test no green light. I do have power to brake light on trailer.
  3. P

    Better battery life.

    What is the best way to charge and keep a new deep cycle battery charged? I use battery for trolling motor and lights,I have a older 6- 12 6 amp&2amp charger is this ok to use, or is their a better charger?What about the on board chargers?
  4. P

    Compresson relief on outboards?

    I was talking with someone that told me that all small engines have a compression relief, and that a compression tester on out boards is useless, true, or not true? This person has a lot of experience and schooling on small engines and chain saw motors.
  5. P

    Replacment of motor

    Thinking of replacing motor, but how do I determine to go with a long or short shaft putting on a 15 foot sea nymph tx 150 25 hp max 770 lb max weight. Thinking of going from 1963 10 hp to new 15 hp E tec
  6. P

    New battery help

    Will be needing new battery for terova 55lb thrust trolling motor,and fish graph will use boat lights at times,will just about any deep cycle battery do? ?ow do I tell good from bad?
  7. P

    Floor repair sugestions

    So I am replacing floor on my fishing boat a 14 foot alum. flat bottom,it had carpet I don't really want to go back to that, what other materials are out their? I was thinking the marine vinyl from Cabal's but a couple people told me it is slippery, they suggested the rhino coat surface or deck...
  8. P

    ring replacment 4.5

    I have a 4.5 Mod.J5RCSS that will run if I turn the fly wheel fast with a drill but not with pull rope, If I replaced rings is it as simple as removing the head and replacing rings or should I have a shop do this? I am thinking I will need to remove connecting rod and pull piston up to get to rings?
  9. P

    Lower unit leek,

    Is their a pressure test to determine where a lower unit is leaking? My motor had water in it when I drained for the winter,Is their a affordable tool a guy can buy to check?
  10. P

    Any hope for this battery?

    A deep cycle I noticed it discharged in a couple of days just setting, now it won't hold or take a charge is their any hope for it?
  11. P

    spark plug wire replacment

    After I tried the suggestion on starting I believe now I have a bad plug wire, any way I cannot see how the armature plate can be removed for wire replacement,or do I not need to remove it?
  12. P

    10 hp hard starting

    Well my this motor has had new points and wires condensers and plugs ,It starts and runs like a new one when warm, I mean one pull and it's running .But if it,s cold, I all most regret taking up fishing as a hobby it starts so hard. I pull the choke and it just don't seem to get fuel to get that...
  13. P

    Rewind spring repair help

    The rewind spring on a 1962 10 hp how hard to replace one , cannot find any information on this.
  14. P

    Help with ID on this boat

    Last seen on Diamond Lake, Michigan. Cool.
  15. P

    Plug wire replacment

    I found a bad spark plug wire on a 1962 10 hp I am wondering how to remove the plate that holds the coils and points, I see screws in between power head and plate but how to get to them. the wires are tucked under the plate.
  16. P

    Tryied out trolling motor

    Used my 55lb thrust on 18 footer this past week , worked great! Also used remote and tracked speed at 9.9 mph. From what I read that is about all I can expect from a 35 hp. But thanks for all the help.
  17. P

    I'm ready for fishing season

    Just wanted to say thanks for the many replies to get the motors ready for another season.:joyous:
  18. P

    compresson on 10 hp?

    what is acceptable compression on 1962 10 hp ,I have 65 psi on both cyl. with cold motor, is this ok, also how do I set gap for fly wheel and magneto? I have new points set to 0.20 and new coils but one set of points are not firing.
  19. P

    Where to start Points or Carberation?

    A 1962 10 hp: I know its old, but It starts hard. I am thinking the first thing would be is a compression test then replace points? It runs pretty well after it starts but some times even after it is warm, I need to choke it and then hope for the best, I know its old.
  20. P

    Cheap troling motor mount

    As I posted on pontoon thread, I want to use the trolling motor on pontoon also, being retired, I needed to come up with a cheap idea. This is what I came up with. I am going to use a thinner stile super strut on pontoon, and add a lock to idea.
Top