Now Now...there is not one single thing about being lazy using acid to verify the glass's state of condition....Sometimes it takes small steps before running full on...stirring the imagination is just part of the adventure..lol
Speaking of running full on your boat is quite well done, I am...
Well even old girls need love...
1. Go to say ace hardware, pick up some Wood Bleach. Mix as directed put the solution in a say weed pump and wet the boat with the solution. Keep the boat wet with that solution as long as you can pay attention to it. RInse and it should brighten...
Check your fuel pump pressure at the first cold start, while i am not sure of your fuel pump cell it should pressurize then stop. Have a gauge on it during that process, i would be amazed if you did not see a good blip in pressure...Or a drop to after the first few turns of the engine.
Not to much experience here with this type of setup, 78 Glastron GT 150 675lbs dry weight add 400lbs total load 1000 lbs.
1977 Johnson 70hp 2 stroke 120 lbs compression on all three cylinders runs very strong. Turns a older 3 blade right to 6000.
I believe it a 2.25 drive ratio.
So I use...
So being new with a outboard i know enough to use this forum. Made simple the outboard is riding 2 inches low i need to raise it at least 1.5 and I believe Its raised to its maximum height already on the transom. Input advice would be greatly appreciated in terms of raising the engine....a...
Made short and simple the center hole has 20lbs of compression dead as door nob. With that being said the rest of the motor is in fine condition ive had it going to 5 minutes If this were a v8 engine i would know how to move forward but a old two stroke i have no ideals or experience with on how...
Model 65373r
Serial J01350
So being a complete newbie to out boards i am seeking some direction, made simple the motor was checked for compression yielding some poor results. Cyl 1 110 cyl 2 20 cyl 3 90 psi. Carbs starter ignition actually every thing aside from the sea pump is in good working...
I have recently run into this outboard it belongs to a close friend, so before starting it I replaced the water pump. No problems getting it off but now I cant get the last inch to mate up.It was disassembled in the forward gear released the shifting rod etc, it goes in smoothly I try to rotate...
Ok so i have seen a lot of threads and have lived with the SX drive vibrating fairly hard on turn's left of right only...trimming is another world only at very high (high articulation) does the drive shrudder. So the drive is off and the knuckle's are as free and easy turning as one could hope...
A mature (over 70) lady gets pulled over for speeding...
Older Woman : Is there a problem, Officer?
Officer : Ma'am, you were speeding.
Older Woman : Oh, I see.
Officer : Can I see your license please?
Older...
Ive just spent 3 hours trying to fix a new washing machine my head was a bit foggy so i came to do a little RR and look at more important issue's but when i get in here all i see are parts comercial's for GE washer's....Really guy's ..:faint2:
http://www.volvopenta.com/volvopenta...V6-240-CE.aspx
http://www.volvopenta.com/volvopenta...V6-240-CE.aspx
Direct fuel injection.
The move from multi-port technology to direct injection means atomized gas enters the combustion chamber at 2250 psi. Compression ratios of up to 11.5:1 create a...
My power steering cooler is leaking and I was about to replace it then I began wondering what on earth for. With today's modern oil and the low temps that exist on a marine engine is this just overkill on a little I/O...
The temp gauge has taken on a new life that is when at idle it run's a solid 165 no bouncing rock steady as it always been. Now when I go on plane it drops to 120...3500 rpm and above. Ive replaced the sender unit with the exact same result's. The engine and riser's do run cool and I can see and...
I have gone from ac43 to ac44 simply because the 43's would get pretty dark after a year or so...So i put in the 44's and after one tank of gas..40 gallon's the plug's are still pristine white...should i not have gotten some discoloration???
