Search results

  1. jasper60103

    85 evinrude 25hp power head gasket

    Nice job. Good call on the head gasket. Sounds just like my old 30 hp Johnson. Darn good motor. Enjoy it.
  2. jasper60103

    Where is the lowest prices for new outboard engines?

    None of usual online dealers have any 20-25-30 hp motors in stock. Hopefully you get it sooner. Enjoy the new motor.
  3. jasper60103

    DF30 LU removal

    The procedure looks straight forward and similar to OMC motors I’ve owned in the past. Just wondering if there are any gotchas? This will be my first water pump change on this motor and want to do it right. Thanks in advance for your help.
  4. jasper60103

    DF30A oil filter change

    I read in the owners manual says the oil filter should be changed by a Suzuki dealer. I plan to let the dealer do it, but do you know any reason why this isn't a DIY? Thanks. jasper
  5. jasper60103

    1980 Evin 25hp now dies

    See # 84... >
  6. jasper60103

    fuel pump diaphragm?

    I'm looking to replace the fuel pump on my '88 30 HP Johnson. The donor is from a '87 30 HP Evinrude. After looking up the part, I see everything is the same between the two assemblies except for the diaphragm (0334640 vs. 0332678). Any idea what the difference is? I would rather swap out the...
  7. jasper60103

    1988 20hp evinrude converting to 35hp & adding electric start

    Bowfisher, I've never adjusted timing before either, but you may want to look at Joe Reeves WOT timing procedure in the stickies... http://forums.iboats.com/forum/engin...edure?t=228183 This is a non-running method to adjust the timing advance at WOT. Currently, there is a bolt with a rubber...
  8. jasper60103

    1979 25 hp evinrude 25904r manual needed

    Not sure about finding a PDF, but you can generally find hard copies of the OEM factory service manual at a reasonable cost on ebay...
  9. jasper60103

    Lower unit drain and fill screw gasket question

    I came across the same plugs on my '88 Johnson 30hp as shown in the pic below. They use the o-ring type seals. I changed my plugs to the ones w/o the o-rings, and used the plastic washers, but this was probably unnecessary.
  10. jasper60103

    '87 Johnson 30 water pump swap question

    Yea, I recall the brass bushing (#57) you're referring to. Yep, it should just slide off. Is this a salt water motor?
  11. jasper60103

    Johnson 35hp longshaft conversion...

    According to the model number (35753H), it's actually a 1977 which should fit your motor. http://www.ebay.com/itm/Early-80s-35hp-Evinrude-OMC-Long-Shaft-Lower-Unit-and-tower-housing-/171788237923?hash=item27ff607c63&vxp=mtr
  12. jasper60103

    1967 evinrude 33hp - safety switch question

    I copied this from a '64 28 hp Evinrude service manual. I think it applies to your motor as well. Good luck.
  13. jasper60103

    red paint flakes in fuel tank

    I noticed small red flakes as I was draining my metal 6 gallon fuel tank (for the second time). I'm assuming its flaking from the inside. I was wondering is there a fix for this? jasper
  14. jasper60103

    Rough Running Johnson 30 HP

    Re: Rough Running Johnson 30 HP Yes, I see it. Thanks. Timberwolf, just another piece of info for the record...
  15. jasper60103

    307551 slotted head drain/fill plugs obsolete?

    I ordered a couple 307551 plug/washers, but was a little surprised when I received a socket head screw. Boats.net says the OEM slotted head screw is obsolete. The manufacturer superseded the part with a socket head screw. Has anyone else encountered this when ordering the OEM part? Can you still...
  16. jasper60103

    1946Zephyr, your 1953 25 hp??

    1946Zephyr, I was wondering how this motor came out? Was it difficult to work on, or parts hard to find? I was looking at one of these motors. http://forums.iboats.com/showthread.php?t=285643&highlight=1953
  17. jasper60103

    clean carb w/o a compressor?

    Well, I never done a carb before, but now I may have to. I don't own a compressor except for a 12V tire pump. edit: Even with the small nozzle attached it doesn't blow hard enough. Can you use the spray carb cleaner to blow it out, or do you have to use a compressor? jasper
  18. jasper60103

    calling F_R and Samo ott

    Can you help me out on this thread?... http://forums.iboats.com/showthread.php?p=2890767#post2890767 Thanks.
  19. jasper60103

    rope starter busted spring

    '81 Johnson 25 hp. Tried to start motor this morning and it wouldn't recoil. Never had a problem before. Anyway, I opened it up and found a broken spring. Before I order the part, I wanted to know should I replace anything else? The pawl seems to operate like it should. As I said before I...
  20. jasper60103

    '81 J25hp shudder problem (video)

    Runs like the wind, but just above idle it shudders and vibrates quite a bit. Notice shuddering at the start. Also at 1:27, 2:23, 3:30. FYI. New L77JC4 plugs gapped at .30. Also, I tried adjusting idle. It doesn't idle as smooth as I would like. It seems the initial setting works best...
Top