Search results

  1. M

    cooling 1999 6hp evinrude 4 stroke

    Yess, tube is in the housing and the gommet is new.
  2. M

    cooling 1999 6hp evinrude 4 stroke

    yeah
  3. M

    cooling 1999 6hp evinrude 4 stroke

    Hi All, I have a 6 hp 4 stroke outboard which has problems cooling. Replaced the impeller ( original), the gommet and the gasket between the stainles steel plate and the housing. I got some flow from the pee hole but no where what it should be. It starts of realy strong for one second and then...
  4. M

    25hp 3cylinder quitting

    Does it start right up again?
  5. M

    1954 cd11 johnson wont run

    Isn't there an inspection hole on the flywheel? Otherwise, use a puller. All older coils end up cracked, unless replaced later on in their life.
  6. M

    1954 cd11 johnson wont run

    You can have a strong spark with cracked coils. Only at the wrong moment. Not a big issue to inspect.
  7. M

    1954 cd11 johnson wont run

    Did you replace the ignition coils?
  8. M

    1971 Evinrude fisherman, not pumping water

    If the brass pipe is not correctly in the gommet it can push out the gommet when you bolt the lower unit on. It the brass long enough and not bended? When it is misaligned, it can bend.
  9. M

    1971 Evinrude fisherman, not pumping water

    If you hook up a waterhose on the brass pipe, does the water come out of the thermostat cover? Did the old impeller come out in 1 piece? Rubber gommet on top of the pump housing in proper condition?
  10. M

    newer powerhead on 1957 5.5 fisherman

    Oke, I will sell it as is. Thanks for the reply's.
  11. M

    newer powerhead on 1957 5.5 fisherman

    I know it's a different gasket but exhaust housing of a 57 or newer one look the same to me.
  12. M

    newer powerhead on 1957 5.5 fisherman

    Thanks for the reply. Regarding your experience I take that as the truth. Just for my interest, why not?
  13. M

    newer powerhead on 1957 5.5 fisherman

    Hi All, I have a realy good looking evinrude 5.5 fisherman from 1957-ish. Powerhead is totally worn out. I will not be able to find a used powerhead from the same era that I can fit here in the Netherands. However, a lot of newer style late sixties and seventies 6 hp motors/ powerheads with...
  14. M

    df9.9 runs for 5 seconds

    Maybe that the lower cylinder ran too lean and did not ignite? I don't know but I am happy I found the problem.
  15. M

    df9.9 runs for 5 seconds

    It turned out to be a clogged idle jet.
  16. M

    df9.9 runs for 5 seconds

    I will check with a timing light. The motor has 2 sparkplugs igniting simultanously. Just one ignition coil for both cylinders. I had a motor once that sparked correctly outside the cylinder but didn't spark inside. Hope thats the issue with this motor as well. Spark plugs will arive tomorrow.
  17. M

    cooling johnson / evinrude 9.9 /15 fourstroke 1998

    Old impeller was intact. But I have no idea wat happened with the motor before all this. Replaced the impeller ( not original) 2 years ago but I remember that it wasn't cooling very strong. It also looks like it does cool good sometimes and than suddenly does not cool. Water is deep enough. Is...
  18. M

    cooling johnson / evinrude 9.9 /15 fourstroke 1998

    Hi All, I've repaired a lot of outboard and fixed a couple of 9.9 / 15 hp fourstroke evinrudes and johnsons. And almost all of them had bad cooling after replacing the impeller. I have one now which has the same symptoms. Is there like an o-ring which is known to cause problems? I want to get...
  19. M

    df9.9 runs for 5 seconds

    Thanks for the reply. It is a 2 cilinder with 1 carburettor. If I play with the trottle I can prevent it from dying but it takes a lot of effort. I dont think this one adjusts the timing. There is however an electric choke. Not a butterfly valve but a small throtte body with a needle. I think...
  20. M

    df9.9 runs for 5 seconds

    Hi All, DF9.9 electric 2015, carb version remote control I got an outboard from a friend. It has sunk, they took it out of the water and gave it to me( after a week). Got the water out and got it running properly. changed the oil a few times. It ran well for a couple of hours. I let it run...
Top