Search results

  1. HighTrim

    58 35hp RDE-19C Shut down issue

    Re: 58 35hp RDE-19C Shut down issue here is the wiring diagram.
  2. HighTrim

    1955 25hp Evinrude Big Twin Lower Unit part 18-0882 ??

    Re: 1955 25hp Evinrude Big Twin Lower Unit part 18-0882 ?? The gasket is used with the shift rod bushing where applicable.
  3. HighTrim

    Pressure test 2 line fuel tank

    Re: Pressure test 2 line fuel tank Ok here is how to test the running ability of a tank, but you still need the motor. If you want a gauge they are easy to make, I can sell you one 10 percent off. :) Now, I suppose you could "pressurize" a tank by blowing air into the air line after...
  4. HighTrim

    1960 johnson 40hp rds-22

    Re: 1960 johnson 40hp rds-22 That wiring is junk, sorry. Now, I don't see where you describe what it is doing? Not starting? You can start it by jumping the starter from a known good battery to get it to run, or pull it over. Then, replace the wiring as needed.
  5. HighTrim

    removing rust from 6 gallon tank 1961

    Re: removing rust from 6 gallon tank 1961 I like to use electrolysis to remove the rust.
  6. HighTrim

    Help Choosing Control Box FD-10

    Re: Help Choosing Control Box FD-10 Borrowed this from another site to show. Yes there is a factory piece you can buy. Post a wanted ad at aomci.org in the webvertize and someone will be able to help.
  7. HighTrim

    1956 Johnson 30 hp RDE-18 12 volt conversion

    Re: 1956 Johnson 30 hp RDE-18 12 volt conversion The choke solenoid will be marked on the bottom with 12V, the 6 volt choke solenoid will have nothing. You could also just wire in a resistor, they can be found at NAPA
  8. HighTrim

    Johnson HD 2 5

    Re: Johnson HD 2 5
  9. HighTrim

    Johnson HD 2 5

    Re: Johnson HD 2 5
  10. HighTrim

    Johnson HD 2 5

    Re: Johnson HD 2 5 Mid 1949. I have an HD26 parts manual, let me look for a HD 25 manual for you. The following should help for now.
  11. HighTrim

    TD-20 Coils?

    Re: TD-20 Coils? Yeah, they can swap, as long as the mfd is the same as stated above. here are some tables to help with cross reference with OMC.
  12. HighTrim

    1956 Evinrude Q's - pics

    Re: 1956 Evinrude Q's - pics The 6 volt starters are fine with the 12 volt batteries. The starter solenoid must be 12 volt, as does the choke solenoid. 12 volts will fry a 6 volt choke solenoid pretty quickly. I have not had a problem with the mercury switches. Another option, which is...
  13. HighTrim

    QD12 shift rod O ring replacement.

    Re: QD12 shift rod O ring replacement. Well Im not sure if it can be taken out or not without removing the bushing, but it is so easy to remove the bushing Im not sure why you would want to try. You can either buy a special tool for removing the bushing which works perfectly from the link I...
  14. HighTrim

    Wiring switch to starter solenoid etc.

    Re: Wiring switch to starter solenoid etc. Im not 100% sure if you can get that to work on a magneto ignition. Maybe, using 2 wires, and simply use the kill button to stop. It is a much more expensive switch than you need though. All you need is a simple, cheap magneto switch. Another...
  15. HighTrim

    Wiring switch to starter solenoid etc.

    Re: Wiring switch to starter solenoid etc. Here is a more simple diagram to use. Instead of the stop button, those 2 black wires will go to the M posts on the keyswitch.
  16. HighTrim

    Wiring switch to starter solenoid etc.

    Re: Wiring switch to starter solenoid etc. This should help. Only need 4 wires off key switch.
  17. HighTrim

    1959 35hp Evinrude Lark - ignition wiring question

    Re: 1959 35hp Evinrude Lark - ignition wiring question Here is your wiring diagram.
  18. HighTrim

    1951 Johnson TN27

    Re: 1951 Johnson TN27 Believe this one will work for the TN.
  19. HighTrim

    1950 7.5hp Fleetwin Prop shaft removal

    Re: 1950 7.5hp Fleetwin Prop shaft removal Do you have the gearcase removed right now from the exhaust housing?
  20. HighTrim

    Evinrude 25HP Not Starting

    Re: Evinrude 25HP Not Starting I don't think I have ever found a head that was perfectly true. I have always had to dress them slightly. It is always low in the center where you found it blown as well, always the last spot to come out when dressing it. I would follow Tims advice so it doesn't...
Top