Search results

  1. Scott06

    Mercruiser alpha lifting point

    You can hang it from there, I usually lay mine on the floor under the trailer can’t get damaged if it’s already on the ground
  2. Scott06

    I have a leak.

    The wye pipe can corrode through, also if you loose a flapper they can lodge in the bottom of the wye and wear through. could be any of those things. Need to look with scope camera or pull the engine and put the boat in the water so you can get in and see what is going on
  3. Scott06

    Need advice choosing an engine.

    Unless money is no object or you want to improve performance I would do a compression and leakdown test on it before deciding to replace it. If you are doing the work and have the ability to lift it, its really not so much work that I would let the fact you need to pull it drive replacing it...
  4. Scott06

    Gen1 oem impeller kit (frustrated)

    its the orange thing just below the impeller in the pump kit shown above. I have usually found that going OEM for impellers and components is best
  5. Scott06

    Distribution housing leak?

    they tend to crack. I believe @Bt Doctur rigged up a replacement made out of copper tubing
  6. Scott06

    3.0 engine removal

    Measure the height of your lifting set up. Most standard hoists wont get high enough to clear.
  7. Scott06

    Milky gear oil

    you can put your drive serial number in here it will take you to the correct parts diagrams https://www.marineengine.com/parts/mercruiser-stern-drive/index.php here is a link to parts breakdowns for 98 and up alpha gen 2 drives- it will be in the gearcase driveshaft. Not sure how old an how...
  8. Scott06

    Gen1 oem impeller kit (frustrated)

    The kits are in the parts breakdown couple different options with and without housings and bases.
  9. Scott06

    Are 88 to 95 4.3 mercruiser stock roller or flat tappet cams?

    If the block is cracked and that is putting water in the oil , it will not show up on a compression test.
  10. Scott06

    1993 classic 25 ft. Bayliner

    Agreed check the structure of the boat before you do anything. If the structure is solid then look at what is going on with the 5.0 and if you want to repower it. Yes a 25 ft with a 5.0 will be under powered. a 5.7 or 383 would do you better.
  11. Scott06

    mercruiser 888 383

    You need a marine ignition like a mercruiser thunderbolt or delco est . Basically all you keep off the 383 is the long block. You will also need a marine harness unless the one off the old engine will work. I think michigan motorz sells the ones they use on their partial engine package .
  12. Scott06

    mercruiser 888 383

    Take off the automotive fuel injection and put a 4 bbl intake and marine carb on.
  13. Scott06

    1997 5.7l water in oil. replace?

    They may be GM makes changes as they see fit and doesnt tell us... You also never know if a wrecking yard engine has been worked on either. Unfortunately you don't know what is in there till you look. And we all didn't think you needed pills to be crazy...
  14. Scott06

    What oil should I use?

    Agreed I switched several cars over from dino to synthetic over the years no issue, including my boat. After repower the warranty required dino oil for first 100 hrs. We are turnign this into another bottomless pit oil thread. The biggest issue OP should concern himself with is he has a flat...
  15. Scott06

    Winterizing 3.7l mcm 224 165 hp mercruiser

    Yes the aluminum block on the 3.7 necessitated a closed system with AF in block , heads and manifold. NOLA told you how to drain the water side of the heat exchanger where the raw water pumped up from the drive cools the AF before it is dumped overboard via the exhaust system. there are a...
  16. Scott06

    Winterizing 3.7l mcm 224 165 hp mercruiser

    Would also check the antifreeze freeze point with a tester. if boat is new to you you don’t know when it was last changed
  17. Scott06

    1997 5.7l water in oil. replace?

    The boat I have i repowered after PO didn't winterize. The block was cracked in the valley after 2-3 uses that spring crankcase over filled and shot oil all over the engine compartment...exhaust manifolds were cracked. Intake did not look cracked nor did heads but didn't want to chance it so I...
  18. Scott06

    Manifolds (Trying to figure out what I am looking at)

    Yeah 15” is fine use the 3” and get on with your life
  19. Scott06

    Alarm goes off when key turns: Low Drive Lube Monitor

    Exactly, last winter I got fishing line around prop seal, when I pressure tested shift shaft seal was also leaking … so I reassessed the whole drive. Most seals were in perfect shape, figured at this point I’ll be good for another 18 years
  20. Scott06

    Manifolds (Trying to figure out what I am looking at)

    I put this 1" plate in to put a O2 sensor for a Air fuel ratio meter could add that to the 3" . Also wonder of the 3 or 6" could be milled down. 6" milled to 4 " or 3" milled to 2" and used with another 3"
Top