Search results

  1. flyingscott

    89 Johnson 60 HP VRO No Start

    Your compression is horrible. Is your starter spinning fast enough? Where did you buy the CDI box from? Do you have a factory manual?
  2. flyingscott

    1982 15 hp Evinrude pops out of gear when slowing down

    Did the shift shaft get spun out during any of these impeller changes? Brass coupler not seated correctly?
  3. flyingscott

    97 Mercury 150HP v6 lower end unit

    I am going to say no because I bet the gear ratio is different. Look at an SEI unit
  4. flyingscott

    System check codes

    Look up Suzuki 140 codes
  5. flyingscott

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Why can't you use a magnet?
  6. flyingscott

    Help with cooling my 1985 70hp evinrude

    The pee hole goes into the side of the exhaust manifold cover
  7. flyingscott

    Help with cooling my 1985 70hp evinrude

    Well the hood looks 85 or earlier.
  8. flyingscott

    Help with cooling my 1985 70hp evinrude

    Kind of a Frankenstein but looks like a early powerhed dropped on the 85 chassis.
  9. flyingscott

    Merc 2003 25hp 2 stroke, sad 😢

    Not true at all. Mercosil can be bored by a competent shop. And rebuild kits are readily available.l.
  10. flyingscott

    1996 Johnson gearcase

    Yes it takes a special tool set the pinion height.
  11. flyingscott

    Outboard to work on minimum throttle

    Just because you didn't understand the question nobody can? Oookaaaay. But I will spell it out for you. He wants a motor that runs at low speeds as well as his 2 strk Malta did. Don't know why you are confused about that. So yes any of the small 4 strks will do that. But yes you should by parts...
  12. flyingscott

    1985 mercury 18hp XD

    Take the hood off and To the right of the carb is the shifting linkage. When you drop the lower make sure the washer comes off with the shift rod.
  13. flyingscott

    Merc 2003 25hp 2 stroke, sad 😢

    2003 should be a blind bore Mercosil block. No head on that.
  14. flyingscott

    Merc 2003 25hp 2 stroke, sad 😢

    On the side of the block are 4 covers on the intake side and 2 on the exhaust. Remove the CDI box and find the covers there. If there is damage it will be on the exhaust side. I would once again question the gage. Every 4.3 I have had is between 160-190 and should be at the higher end.
  15. flyingscott

    Outboard to work on minimum throttle

    How do you know I am wrong? Somebody had to answer his question. Jeez telling him to get trolling plates and props when he doesn't even have a motor? He asked for a recommendation on a motor. Somebody had to answer it.
  16. flyingscott

    Outboard to work on minimum throttle

    Any of the newer small 4 strks will do what you want. Find a dealer close to.you with a good reputation. Another Yamaha 5 hp and under would be an excellent choice.
  17. flyingscott

    Merc 2003 25hp 2 stroke, sad 😢

    Get a different gauge. Highly doubtful it would run much less pull a skier with 60 psi. I would be looking at the plastic bits.
  18. flyingscott

    Mariner 9.9 length

    That is a short shaft 15". If it was a longshaft that measurement would be around 22"
  19. flyingscott

    very cool carb and intake manifold causing moisture

    that tube was to provide warm air to the motor on cold days. without it the motor would have a stumble until it was warm
  20. flyingscott

    Help with cooling my 1985 70hp evinrude

    Put up a pi of the tag and the motor cover and powerhead
Top