Search results

  1. D

    1985 Bayliner 2750 Ciera Sunbridge Resto

    Nice on he hatch and side windows. looking good. something about fabricating stuff is so rewarding. I felt the same way when I did my side windows. All shiny and new. Then I realized I’m gonna have to wet sand compound and polish the hull at some point. Will you cover the windows when you do yours?
  2. D

    1990 Bayliner 2651 resto

    Update 10-9 Last week did some testing with epoxy. Mixed up different batches with cabosil and made some test bonds with scrap wood. Learned quite a bit. Working time to thickening. This past weekend the grinding continues. Found some voids in the transom and filled with thickened epoxy. Gave a...
  3. D

    Setting transom with epoxy

    Again thanks all for the input. Im leaning toward epoxy.
  4. D

    Setting transom with epoxy

    Thanks All! Great information and advise as usual from everyone. Here is my dilemma… And I know this has been discussed and is probably going to create a ton adversity. Epoxy vs polyester to bond the transom. Pros and cons. epoxy- better bonding strength. So say all the research ive done. But...
  5. D

    Setting transom with epoxy

    Thanks woodonglass… I’ve see this before. However I’ve got an I/0. Was hoping to get insight on how much clamping is needed. All west system stuff recommends minimal clamping as to not push epoxy out too much out creating voids. I’ve got some irregularities on the transom due to wonderful...
  6. D

    Setting transom with epoxy

    Okay… question regarding setting the transom in with the west system epoxy. This is for a small transom section on a 1990 Bayliner 2651. It’s not a the entire transom that’s being refitted. Just the middle section. Approx 24 “ x 27”. Here’s what being replaced. after reviewing all options I’ve...
  7. D

    1990 Bayliner 2651 resto

    Haha…. I have nightmares after grinding… I wake up in a cold sweat… worth the aggravation tho. ill keep at it!
  8. D

    1990 Bayliner 2651 resto

    Thanks! Slow but sure…
  9. D

    1990 Bayliner 2651 resto

    Update 9-25 the grinding continues… who knew that snow angles can be seen in Sept. I see now why those that have done it previously hate the job… progress slow but sure
  10. D

    Gelcoat/Paint comes off to the touch

    Compounding the gelcoat…. Then waxing the gelcoat will help restore the boat. I think you’re talking about oxidation of your 30 year old boat. there are many posts on the forum relating the “how to“ on this process.
  11. D

    Using warped plywood for bench seats

    you could screw it to a straight board on one side… glass the opposite…once cured do the other side. Just a thought. Since you have a template you could just get new plywood… might me less time consuming.
  12. D

    1990 Bayliner 2651 resto

    Yep the purple stuff will be used for sure. Update 9-18 was finally able to get some exterior grade plywood for the transom. seems the big box stores aren't carrying much stock these days. Also able to purchase some linear Doug fur for the motor mount stringers. made a template for the transom...
  13. D

    1993 Wellcraft Eclipse196S Rebuild

    Good you’re gonna check …….There’s always hope BUT…been there done that… but ultimately I ended up replacing everything. better safe than sorry. Good luck….let us know your progress. The folks on this site are amazing helpful and very knowledgeable. I’ve learned a ton.
  14. D

    1993 Wellcraft Eclipse196S Rebuild

    I also thought my stringers were good. Took a lot to get the lag bolts out. Top mounts were solid the bottom were toast. Don’t be fooled . Be sure
  15. D

    1993 Wellcraft Eclipse196S Rebuild

    Have you taken core samples on your transom? 1/4” drill bit from the inside. check from the bottom to the top. Go in about half inch. Three samples (low middle and high near the keyhole) check what comes out. do the same on he motor mounts.
  16. D

    trim pump runs but no up or down

    While the cylinders are apart you may want to consider rebuilding. Inexpensive and a great sense of security knowing they are rebuilt. Just my 2 cents… hope you find the issue. Good luck
  17. D

    Actuator rebuild

    Thanks Lou! I’ll search. This will be a winter project.
  18. D

    1990 Bayliner 2651 resto

    Yep… already did. It won’t come out through the engine compartment. it will be taken out through aft cabin.
  19. D

    Actuator rebuild

    Got it! It has 2 hoses so I assume I’m in luck. I’ll search on you tube under Corvette power steering actuator rebuild. Here’s what I’ve got( one hose already removed) sorry didn’t get a full pic. Thank you for the input
  20. D

    1990 Bayliner 2651 resto

    Update 9-10 Dug a little further in removing bilge hose, fuel vent tube , fuel hose, holding tank (with 3 inches of leftover crap still in tank from PO 🤮), macerator pump and capped off the fuel tank inlets. Moved all electrical out of the way. I also removed the steering actuator. Hope to...
Top