Search results

  1. J

    Is this trim end cap usable?

    EDIT: It's metal on metal so it seems like a little pitting wouldn't matter regarding leaks? Also the scraper has lots of play inside the end cap, not even close to a tight fit but it fits extremely tight on the piston. It's the right rebuild kit so I guess that's normal?? It extremely tight on...
  2. J

    Is this trim end cap usable?

    Alpha1 Gen2 Can I still use this trim cylinder end cap? I scraped out as much salt as I could with a pic and wire brush. It's not smooth where the scraper will sit.
  3. J

    Alpha 1 Gen 2 trim seal replacement

    I'm doing a trim cylinder seal replacement. Not taking off lines so it's on the boat. I got the end cap off easily. When I started to pull the piston out the fluid started pouring out tilted up. I pushed it back in and tightened to cap for now. Should I extend the trim all the way out first to...
  4. J

    Possible trim line snowballing nightmare?

    One in the front one in the rear # 815954-1
  5. J

    Possible trim line snowballing nightmare?

    Mercruiser Gen 2. I believe I need to redo the seals on the cylinders. The nuts are frozen. If I strip the threads on the cylinders or lines then I need to change the braided lines. The braided lines all connect to a plate under the transom assembly. If those strip I need to change that plate. I...
  6. J

    Trailer axle capacity/sizing

    5 lug
  7. J

    Trailer axle capacity/sizing

    Shoreline trailers are no longer in business right? I have a single axle trailer with a 2x3 axle. Trying to figure out weight capacity. A google search shows multiple weight rating for that size axle from 3500 to 5200? How do I find out what it will hold. It's built like a brick shithouse. Also...
  8. J

    Is this trailer repairable?

    Entire trailer is completely solid except the area between the red marks on both sides. Dual axle roller trailer seems a shame to toss it
  9. J

    What foam for seats and where to buy

    Redoing seats. What foam (density/ILD) for the 2 back square seats and for the rear section that flips up. That section can be rock hard but the seats I'd like to be somewhat comfortable and also not flatten down to nothing when you sit on them. And where to buy. Foam Factory and amazon stuff...
  10. J

    Free Mercury Tower of Power

    I've been reading that and #1 is the issue from heat. I've also read the bottom cylinder is an issue getting water in from the water jacket rusting out. Any idea how to check that besides water pouring out when I take the plug out. Also wouldn't that cause a hydrolock condition blowing the motor
  11. J

    Free Mercury Tower of Power

    Ya think I can get a new harness for like $250 or possibly cut and splice wires for nothing. Which is my dilemma. How much am I going to dump into a 40 year old motor before I'm in to deep pissing away money and time
  12. J

    Free Mercury Tower of Power

    According to the SN on the transom it's an 84 confirmed by others. Was told someone must have swapped the cowl
  13. J

    Free Mercury Tower of Power

    I can get a free 1984 1150 inline 6 with all the controls. It turns over that's all I know. Seems to be in pretty good shape. I took the plugs out and they seemed okay. I know these motors have a good reputation and a bit of a cult following. I've always had a Mercruiser and don't know the first...
  14. J

    Stainless riser fitment help.. with numbers

    I have a 90 V6 4.3 so it seems like it may work. Any input on flange style (short bolt) vs a normal elbow long bolt? I would think the gasket would stop corrosion between the elbow and Cast iron manifold with the 2 different metals.
  15. J

    Stainless riser fitment help.. with numbers

    Looking to buy used stainless elbows on cast manifolds in saltwater . These are older flange type instead of long through bolts, any issues with that? Riser#816900C Motor# OC753700 Will be replacing manifolds at the same time with new ones Will it work?
  16. J

    Nerding out on seat cushion foam...what to get

    Googling P65 and P80 seat foam and any other combination of words brings up nothing..any help
  17. J

    Nerding out on seat cushion foam...what to get

    Guess nobody likes foam LOL
  18. J

    Nerding out on seat cushion foam...what to get

    Does it really matter that much between open cell and closed cell...anti microbial or fast dry? I'm reading some last between three and seven years and others between 7 and 10... density and all sorts of other stuff..I'm redoing the back two seats and the long flip up section. It's an older boat...
  19. J

    Massive vibrations...then none

    If I pulled one plug wire at idle it sould duplicate the issue if that was it right? Seems like a good way of testing/troubleshooting/eliminating
  20. J

    Massive vibrations...then none

    Also there was no knocking. Just massive shuttering and vibrations like something was about to blow
Top