Search results

  1. D

    Repairing gas sensor / cables / vent gas hose

    id be hard pressed to use that tank. Looks a bit scary. Pull it and inspect if possible.
  2. D

    1990 Bayliner 2651 resto

    Ah… I see what you did there. A picture is worth more than words. Thanks
  3. D

    Math problem

    Well I’m no math wiz but here’s my thinking 50:1 ratio in a one gallon tank would mean 2.6 oz of 2 cycle oil is needed. In a 6 gallon tank you would need 15.6 ( roughly 16) oz of 2 cycle oil. Since you had only 1 gallon of fuel in the tank and you put in 16 oz. You would need to add roughly 5...
  4. D

    1990 Bayliner 2651 resto

    neoprene was used under the tank as shown. was thinking the same on some kinda top support. The factory only had a single strip of a 1x2 across the top of the tank.
  5. D

    1990 Bayliner 2651 resto

    Update 7-21 fuel tank is in. using plastic baseboard on each corner with pl marine adhesive. Started on the starboard side front corner. Using wood splitting wedges to help keep the tank snug while the adhesive is curing. then starboard side aft. fabricated solid piece of linear fir...
  6. D

    Building a '93 Caravelle 1750 Classic Bowrider

    Nothing beats being on the water!
  7. D

    Is this trim end cap usable?

    I’d try and get the surface where the last last washer sits a bit cleaner. Emory paper? and be sure the channel where the final c clip that holds the washer in place is clean. Since the seals are inside the cap you should be good to go. Good luck
  8. D

    Is this trim end cap usable?

    Did you replace the seal In the cap?
  9. D

    1990 Bayliner 2651 resto

    Also epoxied up the old holes for trim tabs and fish finder. While I was at it I drilled out the outdrive holes ( a smidge over sized) and epoxied those up as well. Ya know the little details. Getting it done!
  10. D

    1990 Bayliner 2651 resto

    7-6 very hot temps today. 96+… got out early and put he second coat of paint in the aft locker. also put a layer of 1700 on the fuel tank shelf. The tank may get installed tomorrow.
  11. D

    1990 Bayliner 2651 resto

    7-5 More progress. Finished replacing the after locker. Used polyester resin in 90 temps. Stuff was kicking off in like 10 minutes. 🤣 Made small batches about 8 oz at a time. dry fit the board. tabbed in with 6 in wide csm. Very happy with how it came out. A little paint and she will look purdy.
  12. D

    Fuel tank fitting

    Got it! Thank you Chris
  13. D

    Fuel tank fitting

    Question….. what should be used on the threads of this fitting. In addition what is to be used on the fuel fill rubber line? I know about 2 hose clamps must be used on each end. Is there a sealant to be used? Any help would be appreciated.
  14. D

    Gas leaking out of one carb?

    It was me… glad you got it sorted out. Happy boating.
  15. D

    Replacing seals on power steering arm

    Found an old thread on here. Ordered a seal kit. Same setup as on an old corvette. Less an $40. I‘ll keep y’all posted if the fitment is correct🤞🏻
  16. D

    Gas leaking out of one carb?

    check the service manual if you have it. if not search on line.
  17. D

    Gas leaking out of one carb?

    Did you replace the needle? i used a qtip with a dab of brass o to polish up the brass needle seat in the bottom of the carb. That helped mine stop leaking. Did you check the float height?
  18. D

    Replacing seals on power steering arm

    Anyone replaced the seals in a mercruiser power steering actuator? Im fairly certain that it would be available from an auto parts store. Part numbers and any tips on how to rebuild would be appreciated. here’s the part I’m looking at.
  19. D

    1990 Bayliner 2651 resto

    Thanks! Kcassells! Glad your following
  20. D

    1990 Bayliner 2651 resto

    Maybe…it was incredible how fast it cured..I wanted my first attempt on something less critical to the structure of the boat. happy with the results.
Top