Search results

  1. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-10-2011 Update 02-10-2011 Last night finished taking apart the mid section pieces. Had to buy a 1 7/8" socket to get the nut off the pivot shaft. I will purchase a new one, but will the collar/bushing also need to be replaced at the same time. Also should the teflon bushing in the...
  2. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-09-2011 Update 02-09-2011 Last night I did not get the boat moved like I had planned. The spot where I was planning on moving it to, had to have some snow removed first. Tonight is the night it gets moved. Instead I played with the mid and lower sections of the motor. I fist removed...
  3. j_k_bisson

    Lake Trout!?!?!?!?!?!?!?

    Re: Lake Trout!?!?!?!?!?!?!? What we generally do on Lake Erie is use downriggers. I use two Bigjon downriggers off the back corners mounted in the gimbal mounts. Here is a pic of the set up of the boat. If you look to the right side you will see the downrigger and my stackers. The other...
  4. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Re: Update 02-06-2011 Re: Update 02-06-2011 Last night finished cleaning the end caps/bearing carriers. Also finished scrubbing three pistions. Still have three more pistions to go. Tonight I plan on moving my boat over to my buddies house seeing I have that By Law Infraction to take care of...
  5. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-06-2011 Update 02-06-2011 Last night finished scrubbing all the linkages and minor switches. Here is a pic of all the parts back into place. The reason I do this rough assembly is so that I can make sure I got all of them. I also can figure out how they go back together. Here is a...
  6. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-05-2011 afternoon Update 02-05-2011 afternoon This afternoon I was able to get to rebuild the VRO fuel pump. I used the "Maxrules" method for dissassebly and assembly. On his website you can buy the rebuild parts. This is only for rebuilding the fuel side. I only plan on using premix...
  7. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-05-2011 Update 02-05-2011 Well last night rebuilt all my carbs. Basically took them down to bare housings and screws. Soaked and washed them in a larger butter container of varsol and compressed air dried them after. Then reassembled oll of them with OMC carb kits. I noticed where...
  8. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-04-2011 Update 02-04-2011 Well last night ripped into the throttle body and carbs. Did not actually get into rebuilding the carbs. Just took a ton of pics of the hose routing before taking the whole system apart. If anyoe needs to see the pics of the hose routing then shoot me a PM...
  9. j_k_bisson

    Anyone a whirlpool repairman?

    Hello to all. Looking for some help on my Whirlpool side by side fridge. Just wondering if there are any appliance repair men/woman here. If so please respond. My fridge (GS2SHAXLB01) stopped freezing last night. Yesterday noticed a burnt electrical smell in the kitchen. We could not locate the...
  10. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-02-2011 Update 02-02-2011 Last night went back out to the garage and finish cleaning up the intake manifolds and the reeds. Cleaned up the old gaskets and ran taps thru every threaded holes. Here are the pics of the completed parts. A question about reeds. I had one pedal on all...
  11. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-02-2011 cot'd Update 02-02-2011 cot'd Next I layed out the rough spot for the drilled hole that Faztbullet directed me to do. Is this right place? I was wondering if I sould make it so the the hole lines up with the edge of the crank seal ring flange. Or do I want to raise it up a...
  12. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 02-02-2011 Update 02-02-2011 Seeing today is a snow day. After I shoveled the drive I went out to the garage and started cleaning parts. I started with the heads. Totally torn down the heads. Then sprayed them with brake cleaner and scrubed them with a brush. Next I scraped off all the...
  13. j_k_bisson

    1991 Bayliner Trophy 2002 Transom Repair

    Update 02-01-2011 Update 02-01-2011 Well this post is an update on the motor and to post a pic of the other boat (my buddies) that we have been building from scratch. The Motor. Have block tore down, cleaned, inspected, and ready for reassembly. Hope to have all the block parts in by Friday...
  14. j_k_bisson

    Talk me out of deglazing block myself

    I'm looking at a 250-300 for deglazing a 225 evinrude block. The block specs out nicely, well in tolerence. Just wondering what the major reasons would be no to go out and buy a deglazing hone and do it myself. Anyone every try this? What where the results? How much does deglazing take off...
  15. j_k_bisson

    Need help identifying a flywheel

    Need help solving a mistery. It's a flywheel that came on my frankenstien 225 evinrude outboard. The casting numbers on it where 583146 and the stamped number in it was 16F L3. I need to find out what year outboard this flywheel is for. Any and all help would be appraciated. Here is pics of the...
  16. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Re: Update 01-30-2011 Rev-2 Re: Update 01-30-2011 Rev-2 Here i this afternoons progress. I measure3d all hte pistons. I still need to analysis the data. Then I removed the crank seal rings. I measured those and four of them need to be replaced. Here is a pic of all of them and then the four of...
  17. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Re: Update 01-28-2011 cont'd Rev-2 Re: Update 01-28-2011 cont'd Rev-2 Well last night spent the first half of the night cleaning up the block. I cleaned every gasket surface with a razor blade, file, and brake cleaner. Then cleaned out evey threaded hole by running a tap down then blowing them...
  18. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Re: Update 01-28-2011 cont'd Rev-2 Re: Update 01-28-2011 cont'd Rev-2 What is the the manifold you refer to? The exhaust or the intake/throttle?
  19. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 01-29-2011 cont'd Update 01-29-2011 cont'd The dissassembly on the block ended last night around 12:30am. I ran into a wall, it was a 5/16" 12pt socket I did not have. Actually I just got home from town trying to find one. Could not find one anywhere that was open on a Saterday. All the...
  20. j_k_bisson

    1987 Evinrude 200hp outboard resto/rebuild

    Update 01-29-2011 Update 01-29-2011 Well the night started like this; I'll show you how the night ended later in the next post. I was able to find all the part numbers and casting numbesr to help identify the parts. Here is a pic of the carb side plate. You see the number clearly. Have not...
Top