Search results

  1. boatdude100

    Outdrive Paint & Prep

    Question about above for V.P outdriver. Should the JB wield perhaps go on top of a first layer of primer as the primer is corrosion prevention? If so, would it (or marine tek) stick well to a primer? like self etching primer CDN tire or alodine? Also, Zinc chromate primer is no longer available...
  2. boatdude100

    Corrosion paint SX-A outdrive

    Thanks, I will look. Both zincs are there although one is aparantly magnesium (amazon purchase). Freshwater only, stored in lake then trailer through winter. Bad corrosion all around transom. Has anyone tried marine-tek below the waterline?
  3. boatdude100

    Corrosion paint SX-A outdrive

    Serious problem. Corrosion has compromised the seal of my (in the water behind the transom) SX-A outdrive trim motor. Bought the $2400 replacement trim motor and when replacing, discovered that corrosion compromised the seal (eaten away the metal) so water got in trim motor and killed it! Need...
  4. boatdude100

    SX-A tilt / trim pump replacement tips?

    I saw this thank you. I'm going to do it based on this video. I was hoping for a few thoughts from people who have done it. I hear it's a relatively common problem. Anyone?
  5. boatdude100

    SX-A tilt / trim pump replacement tips?

    I'm setting out to do this job. Old one has no activity, suddenly just went silient. Sparked leads at battery when connected directly to battery, no movement, no sound. + and- 12v reads at the connector (relay ok then as I understand it) Instructions seem to indicate I need to remove entire...
  6. boatdude100

    test trim cylinders possible?

    May I ask the process of testing the hydraulic cylinder? You are likely right- its probably electrical however if it is seized and I fry another trim motor... well best quote I have so far is close to $2000 CDN for the part! Better safe than sorry
  7. boatdude100

    drain 9.9 fourstroke float bowl?

    Excellent point thank you. 2010 9.9 fourstroke model 1F10201FK The answer my friends is that the float bowl/carb drain screw is the BRASS 8mm screw to the upper left of the hose that goes down out of the carb.
  8. boatdude100

    test trim cylinders possible?

    I dont want to fry a new trim motor assembly if the trim cylinders are siezed or something. Chan these be tested? SX-A Trim just suddenly stopped working
  9. boatdude100

    Replace or repair SX-A trim / tilt motor possible?

    Trim system is outside the transom under the outdrive. Has anyone ever repaired or replaced just the trim motor or do I absolutely have to buy the whole assembly? Mine is reading open circut, a spark when first jumped but now nothing.
  10. boatdude100

    drain 9.9 fourstroke float bowl?

    Motor went partially underwater with the heavy rain. Where exactly is the screw to drain carb of this motor please?
  11. boatdude100

    tilt trim suddenly stopped working- troubleshooting?

    Did I fry the trim motor by jumping it wrong on Sx-A?? 2 wire motor What I did: from battery: - to green + to blue on connector going to trim motor on transom. Is this the correct procedure or did I just cost myself a lot of money as it shows "open circuit" Please help!
  12. boatdude100

    Trailering boat with outdrive struck down?

    SX-A drive stuck in down position with quite possibly dead trim motor. How can I get the drive lifted -and secured- so it can be trailered? Thanks
  13. boatdude100

    tilt trim suddenly stopped working- troubleshooting?

    So having jumped directly positive and neg to blue and green wires and getting no sound, this means the motor is shot? Q1)Is it true that for a SX-A trim system, the motor is not available seperatly-without buying the whole pricey assembly? Coule not find a motor for SX-A on Amazon or i-boats...
  14. boatdude100

    tilt trim suddenly stopped working- troubleshooting?

    Thanks Scott more excellent pointers. 2 wire motor, jumped as described in my last post. Small spark at battery when touching wire but nothing. No sound, just a welling feeling of defeat in my heart. Also, tested for continuity and found open circuit going to motor at connection Showed +12 v...
  15. boatdude100

    tilt trim suddenly stopped working- troubleshooting?

    Thanks Scott, I did a visual , tightness and corrosion inspection and all seems good with the harness and other wires you mentioned. Not sure how to check it further. I found info on jumping pump/motor and harness with blue and green wire. I will try blue to neg and green to pos and as I...
  16. boatdude100

    tilt trim suddenly stopped working- troubleshooting?

    Just to add.. Boat is a 2007 Stingray I can't even find the motor itself so I don't know what wires lead from it. I did however see a 2 wire connector with a blue and green heavy gage wire tied to the trim sensor wire so I assume that is it? How do I jump it? One to pos one to neg, then reverse...
  17. boatdude100

    tilt trim suddenly stopped working- troubleshooting?

    3L GL Volvo SX drive. Was working fine however, thumb switch has a history of not activating perfectly every time one time out of 20 I have to push it twice. however... I hear clicks when I move the switch both up and down. No motor activation . I'd jump it if I could find clear instructions on...
  18. boatdude100

    When does anode require replacement?

    New to me boat last year 3L GL with SX-A drive with 2 anodes Both are badly corroded which as far as I can tell means either... 1) They need to be replaced or... 2) they are working well... Researched for an hour and still don't understand how I can tell when they need to be replaced?? They...
  19. boatdude100

    added oil to dipstick hole SX-A = damage??!

    Feeling stupid with this one. Filled oil in SX_A drive normally,closed it up, then added small 2 shots of gerar oil in dipstick hole - just to raise level a touch. Was this a bad move?? What did I "lubricate?" Did I do damage? Do I have to open up the top and clean it up asap? Thanks so much!
  20. boatdude100

    Gear oil SX-A -has to be synthetic?

    Have changed SX-A gear oil for winter. Dealer sold me wrong oil - and not enough of it. I will drain/change in the Spring, Q: Should I top up with merc high performance I have left over,,,,, or leave it down about half a L over the frozen Canadian winter? What is in there now is GL5 non...
Top