Search results

you should be able to suss that by checking the clearances. Lucky its not Desmo , my Ducati has another set of shims to clearance the closing rockers ( they dont have valve springs ) too ......thats 16 shims for a 2 cylinder engine and if I hammer it I get about 5000km's . Good fun :LOL:

what , like here ?:LOL::LOL:

I dunno if your referring to AI , but I think its like a naughty child trying to lie its way out of trouble. If you keep badgering it you can get to the truth . I was asking about Chinese stationary 9hp motor ...is the 2:1 reduction on the output shaft gear or chain ( its chain ) ,tells me...

In any event that is a stress riser and I believe it wont get any better , and that if that tube is subject to any stress that crack will propagate ( as in go deeper thru the metal until it fully penetrates ) . Being as how the thing is welded together in the 1st place I think that a...

Yeah , mine's a master , 2GR-fe , we had the 2,4l with the cvt , it was a good car ....untill I wrote it off :D . The master is pretty cool , bit of torque steer when you peddle it at lower speeds , makes overtaking a bit of a wrestle with the steering wheel . My only beef is that its...

Do they provide you with a loan vehicle while you wait ?.... I mean to bad if your trying to run a busness or get to work

If its the same old rubber insulation we used to use it here decades ago to wire up houses , called TRS ( tough rubber sheild ) and it used to give me the 5hits , specially on oven installs usually 2 phase with 400vac across them and the stuff would just crumble as soon as you moved anything...

I figure that ...maybe not correctly , as the valve and seat wear closing up clearance the cam and follower wear opening clearance and with a fair bit of lee way in the clearance spec's the thing ballances out for the useful life of the motor .

Every year vehicles have to be registered ....actually you can do it for 3 months at a time , and we get a registration card that goes on the inside of the screen , NBE826 is the licence plate # and the date is the expirery We can put the rego on hold for 3 months or more , which is free ...

Yeah them new veeeehickles sure are great :rolleyes::LOL: I have a 2003 Toyota Rav4 and a 2007 toyota Blade and I dont get none of that crap .........worst thing that has happened is that the Blade passenger window wouldnt work on auto ........I had to turn on ignition , dont start car ...

Yeah but if one uses decent oil and changes it on time .....just how often do you have to do this ? . I noticed some time ago ( talking motorbikes ) that the clearance spec's got quite a bit wider no motors using these bucket shims .

The number plate on a vehicle . The thinking being that all the remote boat ramps I frequent ( lake Monowai and North Mavora lake ) have only one way in or out ....end of the road sorta thing and cars have been broken into ( not mine ) , so I set up the trail cam to cover both my car and the...

Gawd , I remember as a kid the rod and reel were what looked the best and in my price range , now I have 6 trout spinning rods ......and I think that even if blindfolded I could tell which rod I had in my hand just by the feel of it , and when I go down to the river now days I take at least...

Yeah , just measure the clearance 1st , doesnt matter what type they are untill you need to remove them and you would have to do that to measure the shim before ordering new . as for the 4age , we did 300,000 kms in our MR2 ( aw11 ) and the valve clearances never went out of spec .

1972 ? two cylinder . Id have a good look at the kill switch 1st . If it got no spark in both cylinders its likely to be something common to both .....kill switch maybe

when mine gets home from work ( I dont work ) the 1st thing she does is to see if the dishes in the rack are still warm from being washed just before she got home :D

I leave my trail cam set up when I park my car and or boat trailer in remote areas , least if someone rips me Ill see who it is and get their rego number

The reed stoppers are there to limit how far the reeds can open , you may gain a little power by bending them open a bit more but you also greatly increase the risk of the reeds failing . Typically they will split and crack ,bits then break off and destroy the piston and/or cylinder wall on...

Yeah , as long as they are not damaged a reed hanging open ....even up to a mm is ok , they slam shut pretty quick when the air starts flowing back that way

Far out ! thats a tail and a half .:LOL: