Search results

  1. E

    How to remove the oil seal from a 9.5 evinrude lower unit ?

    Thanks worked perfect and didn’t damage the plate
  2. E

    Can a 6hp impeller work on a 9.5 1967?

    Just had a brand new 6hp kit laying around. I purchased the correct oem 9.5 kit.
  3. E

    How to remove the oil seal from a 9.5 evinrude lower unit ?

    So I have a 1967 evinrude 9.5 and I need to replace the oil seal underneath the impeller but I don’t have a puller. Are there any methods to get it out without a puller and if I need a puller which specific one should I get? Thanks
  4. E

    Can a 6hp impeller work on a 9.5 1967?

    1974
  5. E

    Can a 6hp impeller work on a 9.5 1967?

    Hi everyone, I picked up a 1967 evinrude 9.5 and it needs a new impeller. Could I use this 6hp kit on the left in replace of the stock kit on the right?
  6. E

    Evinrude 6hp gear shifter out of alignment

    Thank you for the information I did realize the shift rod was not properly sling bed far up enough and after re adjusting it lines up perfectly thanks everyone
  7. E

    Evinrude 6hp gear shifter out of alignment

    Well see I don’t believe the power head needs to be removed for this one’s because before I remove the lower unit for the new impeller the shift lever lined up perfectly with the neutral position as well as foward and reverse. I’m just wondering when I put the lower unit back on do I need to...
  8. E

    Evinrude 6hp gear shifter out of alignment

  9. E

    Evinrude 6hp gear shifter out of alignment

    Hi guys so I just got done doing a water pump in my evinrude 6hp fisherman. For some reason I can’t get the shift handle lined up like normal got any ideas of what I’m doing wrong. It still goes into foward and reverse as well as neutral, but neutral is in the foward position and reverse is in...
  10. E

    1974 6hp correct impeller ?

    When I place the new gasket on top of the base plate should I use some sort of sealer or is that not needed ?
  11. E

    1974 6hp correct impeller ?

    Ah okay that makes sense thanks. This is the first I’ve seen the newer kit used on the older 70’s 6hps. Thanks everyone
  12. E

    1974 6hp correct impeller ?

    Hi everyone so I’m replacing the one pellet on a 1974 evinrude 6hp fisherman. When I tried to search the impeller and plate on marine engine.com it seems to show a different impeller than the one on my motor. Am I searching the wrong year? Does anyone know the correct part number for the omc or...
  13. E

    1972 evinrude 9.5 need long shaft or different trim?

    Thanks for the input sea rider I set the trim as you state to 90 deg level with the bottom of the boat. Exactly what shims are you referring too and where could I purchase them. I’m thinking based off your previous picture that the water level is above the small upper plate on the 9.5 and that...
  14. E

    1972 evinrude 9.5 need long shaft or different trim?

    I definitely learned this lesson all of my 7.5hp and below outboard never had this issue this 9.5 seems to be the only one where I’ve had this happen.
  15. E

    1972 evinrude 9.5 need long shaft or different trim?

    this was taken after raising the motor 1 inch. Should this be good to do a test run?
  16. E

    1972 evinrude 9.5 need long shaft or different trim?

    Hi guys not sure if this is the right place for this topic but I got a sears 12ft aluminum boat. Transom measures at 15” my problem I’m having is attached in the video below. I have water spraying up from the back of the boat when going fast. You can see it splashing against the blue wheel. The...
  17. E

    1969 Johnson 4hp shaky throttle

    Hi guys I got a 1969 Johnson 4hp I just took it out today and noticed that when at full throttle the throttle sometimes slowly backs it self down to about half throttle so I have to constantly hold it at full throttle. Is there anything I should tighten up or grease to help this issue? Thanks
  18. E

    1972 evinrude 9.5 need long shaft or different trim?

    Will do thanks
  19. E

    1972 evinrude 9.5 need long shaft or different trim?

    I’m assuming I need to raise the motor like you stated earlier because the Anti-ventilation plate seems to be below the bottom of the boat
  20. E

    1972 evinrude 9.5 need long shaft or different trim?

    Transom looks to be 15 inches that’s why I’m puzzled here.
Top