Search results

  1. FreeBeeTony

    Engine Mount Replacement

    Finally got cooperation from the weather and got my rebuild started: https://www.youtube.com/watch?v=fRugSr17h5k&t=5s :Now time to replace the mounts in the boat. Started by tracing what I could from the original mounts. Planning on frilling oversized holes where the original lag bolts were...
  2. FreeBeeTony

    Break-in Oil

    Not looking /to start a big debate but............ I usually run 20w-50, but wondering what I should use for my break-in, should I sue something lighter?
  3. FreeBeeTony

    Running Engine w/o Alternator

    Want to start engine before installing in boat.....did not remove P/S pump and associated brackets from boat when removed engine, did not want to fool w/ the P/S lines. I'm assuming I can start engine w/ a fully charged battery and maybe connect a battery charger just to keep a charge on the...
  4. FreeBeeTony

    Harmonic Balancer/Pulley

    Installed a new harmonic balancer......came with a bolt and washer. I installed the balancer with a tool from AutoZone and used the bolt and washer to secure. Problem is when I install the pulleys they don't seem to line up........ I am wondering if the washer is not needed. The back of the...
  5. FreeBeeTony

    Initial Start-up

    Plan on starting my rebuild outside the boat a few time to check for leaks etc, I have a full FWC'd system. Plan on using water for initial start-ups...........any problems here?
  6. FreeBeeTony

    SBC Rear Mounts

    Preparing for the installation of my re-build, Plan on getting new hardware for the rear mounts. What are the thoughts on the bushings in the rear cover? How can I tell if they need to be replaced?
  7. FreeBeeTony

    SBC Front Mounts

    Hopefully coming to the end of my rebuild project. One of the last things I need is new front motor mounts. Pretty sure I know what mounts to get. Problem is the "platforms" (not sure what word to use!) that the mounts sit on could use some attention. Can I fill the existing holes with...
  8. FreeBeeTony

    Starter

    Wanting to replace my 10 yr old starter on my new rebuild. Would like to get a "mini' Starter........any suggestions/recommendations?
  9. FreeBeeTony

    Fastener Size

    Coming down to the end of my rebuild and seem to have misplaced dome of the bolts......been doing quite well until now. Right now missing the 6 bolts holding the flywheel to the crank and the 3 holding the coupler to the flywheel; are there 3 "triangular" washesr for the coupler? Can these...
  10. FreeBeeTony

    Reassemble

    Picked up my block, piston/rods, crank shaft, etc., last night. Installed the crank tonight.......not torqued down, just snug. Seems to spin nice.....just coated the bearings w/ oil. Going to take it slow......probably won't start it until spring. What is everyone's thoughts on assembly...
  11. FreeBeeTony

    Replacement Parts During Rebuild

    Should be getting my block back early next week so I can start assembly.....going to take my time over the holidays into early spring. The current engine was ~ 10 yrs old. ​Considering replacing the following: oil pump, water circ pump, starter (definitely), fuel pump (?).... Any other...
  12. FreeBeeTony

    Vibe Damper

    See pics below.........besides the TDC mark not in line w/ the KeyWay.......looks like the rubber is shot. ​Pics are 90* out.......... ​Any opinions on where to get a new one?.................SBC. .
  13. FreeBeeTony

    '95 175 HP

    Looking at a boat w/ twin '95 175HP Merc's. The owner is calling them "tired". ​Don't know hours. ​Are these carbed?..
  14. FreeBeeTony

    Piston Selection

    How's this for a piston to use on my Vortec rebuild? ​
  15. FreeBeeTony

    Engine Removal

    Pulled the engine yesterday.......see pics below. ​Tore it down and got the short block in the basement thanks to my sons. Removed a piston this morning........see pic below. Rings are stuck in the grooves. ​Doesn't look like there was much of a chance saving it.....
  16. FreeBeeTony

    Max Compression

    Hoping to pull the engine out of my boat this w/e. Need to start thinking about pistons. Have Vortec heads w/ 64cc comb chambers. Gonna have the blocked decked so the pistons are 0.015 below the deck and get a gasket w/ a comp thickness of 0.025 giving me a quench of 0.040. What is the max...
  17. FreeBeeTony

    Camshaft Selection

    Instead of building a stroker, I'm thinking of changing the cam in my engine. SBC, Roller Cam w/ Vortec Heads Looking at something like this.: Any thoughts?
  18. FreeBeeTony

    Compression Test

    After cleaning the pistons and cylinders (see before and after pics below). I installed the heads and adjusted the valves. Exhaust/Intake manifolds are not installed. The numbers were not good. All cylinders ~30PSI. I thought maybe it was the gauge. Went to Autozone and borrowed a different...
  19. FreeBeeTony

    Budget Stroker Build

    Have the top end removed and the heads at a machine shop. ​Now thinking of pulling the rest and building a stroker..........on my bucket list. If the cyinlders are OK and can just use a Hone, can I do the clearancing? ​Wanna do it on a low budget!!
  20. FreeBeeTony

    pre-Reassembly

    Preparing to reassemble my SBC. Dropped the heads off at the machine shop...hope to have them back by next w/e. ​Planning on ordering Sierra manifolds/risers to be here maybe the next w/e. ​Below are pics of how the pistons/cylinders have cleaned-up so far.
Top