Search results

  1. dlogvine

    Alpha one gen 2 lube monitor hose leak

    I looked at my boat in the storage and found a little puddle of gear lube under the outdrive, right below the gimbal. Upon closer inspection I found a crack in the gear lube monitor hose. Now, is there a less invasive way to fix it, cut the cracked part out, the crack is located very close to...
  2. dlogvine

    Getting a new drivetrain for Mercruiser 4.3 v6 and Alpha One gen2

    Im not sure if this is a correct forum topic but could not find the better match. However, here is my problem. I just got a nice 2000 Larsen 176SEI hull with everything in perfect condition minus (a very big one too) the engine, transom plate, gimbal and outdrive. Original engine was Mercruiser...
  3. dlogvine

    Alpha One Gen 2 Gear ratio

    I was looking to replacing the outdrive for my 1993 Mercruiser 4.3 V6. The charts say that the correct gear ratio is 1.81 17/19 (I assume 17/19 ,means the number of teeth on the gears?) The outdrive I found on ebay it comes with the following description Alpha One Gen II with 24 24 gear. Good...
  4. dlogvine

    Can i upgrade the engine from v6 to v8

    I am restoring 1993 Larson 210SEI and the running parts are completely rebuil, engine rebored, serviced, outdrive serviced, impeller changed, gaskets replaced. But to my horror when I lokked at the deck under he carpet, it is deteriorated so badly that I will have to replace all the stringers...
  5. dlogvine

    1993 Mercruiser 5.0 Alpha One Gen 2 Bellows replacement

    Im taking on the bellows replacement and can remember for my lifes sake if I need to drain the gear lube from the outdrive or not. Sorry for the stupid question. I change the gear lube in Spring 2018 and did not run the boat (still waiting to fix the deck. Then I noticed that bellows are...
  6. dlogvine

    Started the engine without running water

    I changed the leaking valve cover gasket, changed oil and tested the engine. It ran fine. Then I decided to make a video of the engine running and turned on the engine but forgot to turn the water back on. The engine run without water input for about 10-12 secs. I realized my mistake turned the...
  7. dlogvine

    Mercruiser 3.0LX valve cover gasket

    I noticed that the valve cover gasket on 1994 Mercruiser 3.0LX was leaking oil and I bought a replacement rubber gasket on ebay. Put it on the valve cover, used gasket adhesive, tightened up the cover up to spec torque. Took the boat to the lake today and noticed another valve cover leak...
  8. dlogvine

    2bbl Mercarb for 3.0 Mercruiser fitting fuel inlet thread stripped

    I noticed the fuel leak in the line feeding 2bbl Mercarb. When I untied the fitting fuel inlet thread was stripped pretty badly since the previous owner tied the fitting all the way in while it was at an angle. Is there any way to repair the thread and how if there is. Thank you. Also I noticed...
  9. dlogvine

    1994 Mercruiser 3.0LX with Alpha One Gen 2 gear ratio

    I looked at my Maxum boat outdrive and found out that it is an Alpha One gen 2 model. It has a gear ratio of 1.98 with 3.0LX engine. I found the chart and it does not have any 1.98 gear ratio for this engine/outdrive. The correct ratio according to the following website is 120 & 140 4...
  10. dlogvine

    Bravo One gear lube change

    My friend tried to change gear lube in his Bravo One outdrive for 7.4L Mercruiser (I believe it was build in 1995-1996) and I volunteered to help him. However, first thing I noticed, there was no deep stick screw on the top of the upper unit and there was no drain plug on the bottom of the lower...
  11. dlogvine

    1994 Mercruiser 3.0LX choked

    I took my 1994 Maxum boat with 3.0L 4cyl Mercruiser to the lake first time. At first the engine ran really well, was doing about 35 mph on WOT, cant tell RPMs since this boat did not come with the tachometer. Then after about 45 mins I stopped the engine and jumped in the water to cool down...
  12. dlogvine

    Trailer Bunk screws

    Im changing bunks on my boat trailer and i noticed that the old bunks have the bolts with tying nuts holding them to the trailer frame. I did not take these bunks of the trailer yet, but I wonder as to what is the benefit of using through bolts (or possibly one side bolts, the other side screws...
  13. dlogvine

    23 pitch prop for rebuit Mercruiser 4.3

    I rebuilt 1993 Mercruiser 4.3 v6 engine on Bayliner Capri 1850. It was bored to .30 over, so it definitely added some HPs. Original prop was 19 pitch which is consistent with prop recommendations for this engine. However the fellow I sold the boat to said that it was getting rpms too high even...
  14. dlogvine

    1994 Mercruiser 3.0lx oil leak

    I noticed some oil showing up on the sides and the top of the valve cover of 3.0 Mercruiser. I am lost as to where this oil could possibly come from, since I did not run the engine in at least a week and after I cleaned it up the same amount of oil again showed up ( also very small amount). The...
  15. dlogvine

    Leaking gear lube reservoir

    I found some gear lube under the engine. Looks like the reservoir plastic container is ok, no visible leaks or cracks and most likely the leaking occured through the lower nut or cap that has a hose coming out and two wires (connecting the low lube level sensor?) sealed into it. This nut does...
  16. dlogvine

    1993 Mercruiser 4.3 by rear main seal

    I did a rebuild on this engine and the rear main seal send in the kit was from a Ford motor. So I bought one at the auto store for a similar Chevy engine. Now it looks like there is an oil leak in that area. I wonder if the seals could be different, marine from automotive. And the other question...
  17. dlogvine

    1994 Mercruiser 3.0 fuel filter change. Broken screw

    I tried to replace the fuel filter in the 1994 Mercruiser 3.0l engine. It is housed inside the internal fuel pump housing. To remove it I needed to unscrew the holding bracket and replace the filter. However, when I tried to remove the screw it was rusted in and broke. Should I remove the fuel...
  18. dlogvine

    Replacing old carpet

    I am finishing restoration of my 1993 Bayliner Capri. Almost everything is finished. However the floor carpet that i installed at the edges looks not very professional and a little uneven which is more visual because i kept the old wall carpet. Is there a good link with visuals on how to make...
  19. dlogvine

    Fibergalssing the deck

    I'm going to replace the deck on my 1994 Maxum boat. I removed the old deck and going to cut the replacement plywood tomorrow. I'm planning to cover it with fiberglass on both sides and then use the cloth on the top and cover all the holes if I drill any with fiberglass before putting the...
  20. dlogvine

    1994 Mercruiser 3.0 running smoothly but dies on neutral or low gear

    I am working on my 1994 Maxum with 1994 Mercruiser 3.0 two barrel carb. It is running smoothly when a little gas is added by pushing the throttle but starts choking when Im switching to low gear and dies on neutral. I looked at the carb, Mercarb, and used some carburetor cleaner. It looks...
Top