Search results

  1. A

    lower unit anode 1999 225 evinrude

    Hi guys, well this yr when removing my lower unit anode the bolt broke. anyone know if this bolt is accessible with the lower unit removed? I think it is. Alternatively i'm looking for another way to get a zinc on the lower unit. i was looking for a trim anode but then all seem to be...
  2. A

    Fuel restriction alarm 1998 225 evinrude ocean pro

    Hello All, I'm getting a fuel restriction alarm when going wide open. New water separator was installed and inline fuel filter on the motor. In addtion the fuel line to the primer under the deck was replaced this yr which is what is different. I took the water separator out of the equation and...
  3. A

    torque specs 1993 40hp 4cylinder merc

    Hi All, Does anyone know where i can find the torque specs to replace the head gasket ona 1993 40hp 4 cylinder merc? SN OD194707. Thanks
  4. A

    electrolysis questions

    Hi All, I have a 96 50hp johnson and i'm having electrolysis issues. The small zincs that come on the unit don't seem to be doing much. I'm looking to add but don't these zincs need to be in the water to prevent the damage? I ask because the factory ones don't which i don't understand. thanks...
  5. A

    Water separator question

    Hi All, I have a 98 225 evinrude and i'd like to add fuel filter/water separator. The motor already has the inline fuel filter on the powerhead. Is there any risk of fuel restriction or the water filter removing oil from the gas causing a lean condition and powerhead failure? I run pre-mix and...
  6. A

    1999 225 Evinrude Waterpump change?

    Hi All, Well we went to the Atlantic city air show yesterday(about 15 miles away). We were doing about 3800 rpms and at one point I sped up a little bit and heard a chirp from my warning system. So I backed down the throttle to about 3800 and everything seemed fine. It can not be oil because I...
  7. A

    Bogging 50hp Johnson

    Hello All, just purchased a 96 50hp johnson. The motor runs pretty good but seems to have a fuel issue or something. When on plain the motor will kind of speed up slow down speed up slow down. I believe this would be some how fuel related. The motor is vro injected but I have plugged that intake...
  8. A

    steering questions on 225 evinrude on 22' cuddy cabin

    Hi all, I have a Grady White with a 225 evinrude. My steering cable recently broke and I have a couple of questions. Can I put the new cable back in without removing the motor? The reason I ask is because we had to slightly slightly bend the old to get the right angle to remove. If I do this...
  9. A

    35 HP Johnson konking out

    Hi All, I have an 84 35 hp Johnson and yesterday it started acting funny. I was cruising along at full throttle and the engine whacked out, jumped up like i hit something and stalled. No damage to the lower unit that I can see. She started rt up but will only go to about 1/2 throttle before she...
  10. A

    225 Evinrude gear shaft question

    Hello all, quick question I'm hoping someone can answer. The lower unit has 2 shafts, 1 gear/throttle and 1 drive. This is kind of hard to put into words but here goes. The gear shaft comes down the motor and into the lower unit. At the bottom just before it goes into the lower unit it is...
  11. A

    225 Evinrude missing a beat!!

    Hi everyone, I've gotta 225 Evinrude that recently started having some problems. I just had to replace my power pack to get her running. Starts up good but seems to "kick" like it's missing spark or something. We got a test light and tested for spark which may have been escaping and it was good...
  12. A

    Thinking of buying 50hp outboard

    Hi guys, Found a 93 50hp johnson. Looks in great shape. Guy wants 1500, no controls. Seems like a decent deal from what I've found so far. Any thoughts????
  13. A

    Thinking of buying 50hp outboard

    Hi guys, Found a 93 50hp johnson. Looks in great shape. Guy wants 1500, no controls. Seems like a decent deal from what I've found so far. Any thoughts????
  14. A

    Used outboards wesites?

    Hi guys, I'm looking for some websites for used outbaords. I'm also checking ebay and I've found a few wesbites but they want way to much money. Looking for 50-60hp for under $1000. T
  15. A

    Anchor Winches???

    Ok guys I'm reachin out to the wealth of knowledge on this forum. I want to install a windlass anchor winch on my boat. Only thing is I don't have the launching mechanism already installed on the bow. My question is do they make attachments for the bow to lay the anchor on and if so is anyone...
  16. A

    Replacing the frame around my windshield?

    Hi everyone, does anyone know anything about replacing the metal framing around the windshield? I'm getting pitting and corrosion and figured it would be worth looking into for the future. It's a 22' Grady White CC. Maybe some websites or something....any help is appreciated!! Thanks!!
  17. A

    Which 4 stroke outboard is the best??

    Ok guys what do you think? I've heard a lot of good things about all the different brands but which is really the best? Yamaha, Honda, Evinrude E-TEC 2>4, or the Johnsons? I've been an evinrude guy my whole life and really like these new E-TEC's but are they as efficient as the 4 strokes or is...
  18. A

    1999 225 Evinrude will not even turn over!!

    Hi Guys,<br />Well here goes. Beautiful day yesterday. 10 miles off shore catching black sea bass when I go to start the motor and nothing. All power appears to be good. I turn the key and I hear my normal "chirp" but the starter does not engage. Absolutely nothing happens. Had to get towed in...
  19. A

    Holes for the Trim Tabs

    Quick question, When I installed my Trim Tabs I injected the holes in the hull with 3m 5200 adhesive and smeared it on the hull around the holes but not enough to cover the whole hing area. Close but not quite. They appear very secure. Does anyone think I'll have problems with water getting in...
  20. A

    Black Fish

    Hi Guys, This year I really want to hit some TOG fishing. I've never gone for it but have had it once and it was delicious. I fish in the Long Beach Island NJ area and I was wondering if anyone could point in the right direction to go? I know fishermen don't usually give the hot spots but how...
Top