HELP..1969 evinrude start prob

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
I have a 1969 evinrude 115983E... It ran fine forever, staring with just a tap of the key. Boat is near showroom condition, some old people owned it, and the some of the bolts still have the factory paint from torqing bolts down. The only thing I did to it was replace the wires for the primary coils under the flywheel when i first got it because of small amounts of green death.

One day i took it to the lake and wouldnt start. I changed the plugs and it would run ruff at idle and better at higher speed. I took it home then no start.
I have blue spark from plug to ground..plenty of fuel.. checked the diaphram, connections, coil seems fine.

I looked at a thread of how to test the amplifier, thinking electrical. It said to test the wire on the busy bar Purple/black for 12v with the key on. With the key on and meter set to volts dc, the reading is 0.1 volts. I tested it while turning the motor over and it went up to 8.3v.

Am I on the right path here? Stator? Dist? pick-up? I am completely baffled and need help to figure out my next step. I am the middle of working on it right now and would love an immediate response.
 

JB

Honorary Moderator Emeritus
Joined
Mar 25, 2001
Messages
45,907
Re: HELP..1969 evinrude start prob

No, Drew. You have already said you have hot, blue spark. It is not an electronic/electrical trouble.

Go to the Engine FAQs Forum and do "Outboard won't start". Let us know what you find.

Good luck. :)
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

I was thinking that 8.3v at the amplifier isnt enough right? I realize that sometimes it is a pain to deal with new threads but i have spent two day tring to find the correct info.
So anyone who feels like helping please do so.:)
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

went to FAQ and typed in "outbaord won't start" and found nothing
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

Thanks I found that. I dont think its fuel. Thats wha the thread is telling me.

I drained the bowls on the both carbs and tried to start with just a little bit of added fuel still no response. just seems to try a lil harder tho.

Any other threads that may have some more in depth tips. I have found it hard to search for these threads on the site. i type in "1969 evinrude", "evinrude start", "wont start". What should I type? Where should I look?
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

i replaced the woodruff key at the flywheel.
the compression is 125 lb-psi on 3of them and 124 lb-psi on 1.
no obvious leaks on the carbs.
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

Antbody had similar problems with this model? any mechanics?

Oh yeah replaced the ignition switch today. no change.
 

Elbo

Petty Officer 2nd Class
Joined
Sep 12, 2009
Messages
136
Re: HELP..1969 evinrude start prob

You got spark and compression,The only thing left is fuel.If the timing is ok give some gas.Try a shot in each carb and see what happens
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

I didnt know it was possible to foul the timing. How would I check that. I replaced the woodruff key like I said. It had a somewhat worn one and could have become a potential future problem.

I suppose I could have someone turn the key and try to gauge the piston position at the time of the spark. But say it was off. How would I change the timing??
If I remember it is a direct thing. the stator and distributor set down on a set designated position.

Would the Reverse cut off spring play a role in any of this? even thoough it has been gone over 50 hrs ago?
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

I would appreciate any help. this problem occurred suddenly, without warning.
 

oldrudedude

Chief Petty Officer
Joined
Jul 3, 2008
Messages
480
Re: HELP..1969 evinrude start prob

When you try to start it, does it fire at all or are you getting nothing? After cranking it are the plugs wet? Is fuel actually getting to all the cylinders? Do you get a blue spark capable of jumping a 7/16 inch gap on all cylinders? Have you put a timing light on it to ensure the timing is on?

http://forums.iboats.com/showthread.php?t=228183

I am not familiar with your engine so I can't be specific, but these are the three basics: proper fuel, proper spark, and proper timing. There isn't anything else.

Low speed timing is adjusted with a big screw on the starboard side of the engine. Many people try to adjust the idle speed with this screw and inadvertently mess up the timing.

Drain carb bowls and flush out potential contaminants. Check wires in ignition system for bad wires and loose or corroded connections.

You can get a factory service manual here http://www.outboardbooks.com/index.cfm?fuseaction=models.main&year=1969&ID=57547 Very good investment.
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

Ok...fuel is definitely getting to the cylinders, plugs are wet w/ fuel, no water bubbles, so good head gasket, blocke,etc. Blue hot spark on the the plug itself. Tried to get the fire to jump 1/4" to 3/8" with a screw driver and wouldnt do it. Will check again, more carefully. The advance arm for the timing on the side of the motor hasnt been messed with. The motor only tries to start sometimes for the last second at the exact time of letting off the key. You know the key is in the 'start' position cranking, cranking, cranking, then as I let off back to the 'on' position it sometimes it will cough a couple rpms. This leads me to think either flooding, but more likely advance timing??

this problem started without any warning or messin with the motor.
How does one test the stator?
I tried the amplifier test and was only getting 0.1v with key on and 8.3v while cranking engine. that was the wire on the bus bar (Purple/Black). the test says 12v with key on. It may have been bad test info tho.
 

R8rdrew

Cadet
Thread starter
Joined
May 28, 2009
Messages
14
Re: HELP..1969 evinrude start prob

So does anyone have an idea for the best way to check timing while motor isnt running. I was thinking feeling for compression with plug out and watching spark.
 

brynifer

Cadet
Joined
Jul 11, 2005
Messages
28
Re: HELP..1969 evinrude start prob

I had that same motor back in the day. If you can't get the spark to jump even a 3/8 gap on any cylinders, then I would check the power pack.
I went through a few before coming upon a good one. Your problem suddenly came up out of the blue, as mine did. I was left stranded in the bay for a while though. I actually got a spare power pack just in case
That was a great motor when it ran though. good luck
 

rockyrude

Lieutenant Junior Grade
Joined
Sep 10, 2007
Messages
1,121
Re: HELP..1969 evinrude start prob

On my 115983e I found the two wires that go from the power pack under the flywheel to the sensor were tied down to the timing "arm" and the insulation had worn from the wires moving all the time causing the sensor signal to short to the engine.
 

asdasc

Senior Chief Petty Officer
Joined
Aug 28, 2008
Messages
681
Re: HELP..1969 evinrude start prob

If it tries to start when you let go of the key, it leads me to wonder about the kill switch wires. Are you sure they are wired up properly with the new key switch?
 
Top