Evinrude 1995 40hp running bad on full trottle

Tommyaleks

Seaman Apprentice
Thread starter
Joined
Mar 10, 2017
Messages
33
Hi guy`s. I hope someone can help me with a problem. Evinrude 1995 40 hp no vro. The problem is. the engine runs wherry fine on idle no issue at all but when I start to give it some rpm it runs bad, I have no clean or full rpm, it`s like when something is blocking or to much oil in the fuel. I have done a service on the carburettor`s and they are fine. The floaters are correct adjusted and needle/ seat are fine too. The mixture screws are about 2 1/2 turns out from the bottom. I also have checked the valve under the carburettor, I can blow in both ends of it. so I think it`s fine. Don`t know exact what that valve is or do so if anyone know please let me know. So my next step was to check the fuel pump and I found 1 thing I`m not sure of is correct. it is 3 hoses on the fuelpump, 1 goes to the tree/carburettor`s and 1 goes to the valve and 1 comes from the fuel tank. back of the fuel pump there is a small hole that fits on the small hole on the engine block. but the hole on the engine block was blocked with a screw. it was a little loose and it came a little fuel out of the hole when I screw the screw out. My question is, Shall that screw be there? I can`t figure out why the engine runs so bad on high rpm, and it`s smoking some too.

I hope someone can help.


20170313_131025%202_zpsj1qh8p9p.jpg

20170313_131220%202_zpsr8qdywx5.jpg
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
That spot is for mounting the fuel pump.----With the 3 hose pump that hole remains plugged.-----------With a 2 hose pump you have to take the plug out and mount pump with a gasket.-----Post picture of the " valve under the carburetor " to help.
 

Tommyaleks

Seaman Apprentice
Thread starter
Joined
Mar 10, 2017
Messages
33
Okay I see. I don`t know what the problem is, it running fine on idle, the carbs are fine. the fuel is fine, but still it won`t run on high rpm and it smoking a lot. I think the last owner removed a vro pump on it. Some say when the vro pump is removed you also have to remove the puls limiter and block the hole but I don`t know.
I think this is a fuel/hose`s problem tho.



20170313_191746_zpsahhfjc7m.jpg
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The pulse limiter is a FLOWFUSE and is only needed when VRO pump is used.-----Protects the VRO pump from high pressure pulses.-----What pump are you using now ?---2 hose or 3 hose ?------What are the compression numbers on this motor ?----Does spark jump a gap of 7/16" ( 1 cm ) on both leads ?
 

Tommyaleks

Seaman Apprentice
Thread starter
Joined
Mar 10, 2017
Messages
33
Okay. But can the flowfuse without a VRO pump cause these problems? I am using the pump on the picture above, it has 3 hoses. Compression is 10 on both cylinders, it has a good compression, Yes just about 1 cm. I think it was like 9 mm or something. it`s clean running on idle.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Do not use the flow fuse / pulse limiter if you are using that as a pulse port for the 3 hose pump.---------I for one do not know why any one would use a 3 hose pump on those motors !!!
 

Tommyaleks

Seaman Apprentice
Thread starter
Joined
Mar 10, 2017
Messages
33
I don`t know why. I bought the outboard that way. I got it with the gear house taken off, so I could not hear the engine run, but I was told that the engine was running good. I got the new water pump kit and put it back together and I was able to start it up. it runs fine on idle but not on high rpm`s. I am not able to get hold of that guy I bought it from so I have to fix it my self. I have a fuel pump (in good shape) with 2 hoses from a 1985 50 hp lying in my shop. I will take out the flow fuse and block the hole and try the other pump I have. see if that can help.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
If you mount the 2 hose pump take the plug out between the 2 holes for the mounting screws.
 

Tommyaleks

Seaman Apprentice
Thread starter
Joined
Mar 10, 2017
Messages
33
To day I have changed the fuel pump and have now a 2 hose pump, I blocked the flow fuse hose. Cleaned the carbs again, just to make sure everything is ok. I tried to start it and it did not want to. I tried and tried but with no luck. I also tried to push in the key, I heard the primer pump click but did not wanted to start now ether. And then. I flipped over the red handle on the primer pump and it started right up. switched the red back to normal position. and it run wherry nice on idle, but still problem with rpm. A little less smoke but I have to work it up to high rpm but got no clean and full rpm. Turned it off and waited couple of hours and tried to start it again, and the same thing happen. did not want to start. I had to flip over the red again to get it to start. Any suggestion ?


One more thing, just a question. This thing was right under the outboard leg, do you know what this is for? Do I need it?

20170314_175922_zpsolurjjby.jpg
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The electric primer is NOT a pump.----It is a valve.-----Push key in and hold it in while cranking it over !----Can't tell from the picture what that is.---Post some close up pictures.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Have you inspected the starter motor ?------And what compression values do you have.---Is it 10 atmosheres ?
 
Last edited:

Tommyaleks

Seaman Apprentice
Thread starter
Joined
Mar 10, 2017
Messages
33
the engine is starting and run fine on idle. no problem with the starter. the compression on cylinder 1 = 125 Psi cylinder 2= 125 Psi.
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
There is a small hole on the back of the two line pump you installed. That hole needs a gasket between it and the corresponding hole in the engine block. That hole serves the same purpose as the pulse line (the third line) that was on the three line pump. Vacuum/pressure pulses in that line and through that hole is what operates the fuel pump. If you have not bolted the pump to the block or installed a gasket it is not getting the pulses it needs. The other lines are INPUT from the tank and OUTLET to the carbs and primer system. Are you certain you have the correct hose on the correct nipple? And by the way, 2-1/2 turns out on the mixture screws is a basic setting just to get the engine started. They need to be adjusted for best idle with good transition to mid and high speed response. Too lean the engine stumbles or dies with throttle. Too rich you get excess smoke and very poor economy.
 

Tommyaleks

Seaman Apprentice
Thread starter
Joined
Mar 10, 2017
Messages
33
Thank you so much Silvertip. Yes the gasket is in place and the hoses are connected to the right nipples. it gets fuel. About the mixture screws, I have tried to adjust them in and out but I always get the same problem. I hear the engine stumble when I adjust too lean and so on. it runs perfect on idle but it`s no good on top rpm. I can`t find the sweet spot no matter what I do.

But another question. someone told me if the carb spits/little flow it can also be the reeds. When I told him the situation he told me to check my reeds. Okay, I did so, took them out. Held the reed block into a light and I could see the light trough reed blades. So my question no is. shall the reed blades be closed (no light trough) or is it ok to see light?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
A little bit of light is normal.---------measure with feelers as to how much they are open.--------If it runs " perfect " at idle you do NOT have a reed valve problem.--------------Have you checked for a cylinder sleeve out of position ??
 

Tommyaleks

Seaman Apprentice
Thread starter
Joined
Mar 10, 2017
Messages
33
Do you know what gauge the feelers shall be? Yes at idle is wherry good. Just a little tumbling but not much. No I have not. How to I check that?

Here`s a pic of the carbs after some acceleration.

20170316_1402400_opt_zpspa9plxna.jpg
 
Top